默认没有配置下载引脚,烧录之后下载器将无法再检测到; 使用ST-Link,配置为SW选项: 配置串口 串口开启与芯片模块有关,参照说明更改 注意要手动更改引脚 配置can外设 没有CAN模块配置如下: CAN波特率计算: 1、can分频,4分频:32Mhz / 4 = 8Mhz; 2、公式:SYNC_SEG+BS1+BS2 = T; 2、波特率计算,目标波特率是5...
SW Smith - 《Office of Scientific & Technical Information Technical Reports》 被引量: 116发表: 1996年 Smart Cards and Mobile Handheld Devices: An Overview and Implementation ITL's responsibilities include the development of technical, physical, administrative, and management standards and guidelines for...
【SW】 1. 看是不是reg 有指偏—— 结果排除 SDIO_SLCCONF0_REG = ff3cbf40 ,发现和其 spec 对得起来。。。 2. pinmux 是否设置正确—— 没有问题 确定其C6 sdio fuc = 0 即为 SDIO slave 配置,dump reg:IO_MUX_GPIOn_REG = 0xE02 ...
SW Testing:Control softwarehas been written, and has been used to demonstrate bothSDIOandEMMCperformance. This software is designed to work with theFATFS library. Software testing is currently taking place as part of the integrated test benches associated with separate repositories, such as theVideo...
ets Jun 8 2016 00:22:57 rst:0xc (SW_CPU_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:2 load:0x3fff0030,len:7076 load:0x40078000,len:15576 load:0x...
SYS的Debug选项选择SW,基础时间源选用TIM1定时器,如下图配置 SDIO的配置选择1位宽线程,这一点很重要,我之前选择4位宽线程,挂载系统时总是报出GPIO硬件层错误,困扰了我好几天。SDIOCLK的数值可以参考我的上一篇文章HAL库 CubeMX STM32通过SDIO模式实现对SD卡的读写的配置。本此测试SDIO配置如下 ...
SDIO unveils public database for dial-a-technologyDiane Crawford
SDIO接口协议,官方完整版,包含Part_E1_SDIO_Speciifcation_Ver1.0版本、Part_E1_SDIO_Speciifcation_Ver2.0版本、Part_E1_SDIO_Speciifcation_Ver3.0版本点赞(0) 踩踩(0) 反馈 所需:3 积分 电信网络下载 HDDM-0.8.0-cp311-cp311-win_amd64.whl.zip 2024-12-16 16:15:07 积分:1 ...
This is just from the SW perspective; you would need to take into account the HW point that Shaheen mentioned as well. This isn't an approach that we recommend or support in our current TI OMAP software releases, so you would need to do careful testing of any implementation to watch for...
10 @@ vmmc-supply = <&p3668_vdd_sdmmc1_sw>; }; + sdhci@3440000 { + vmmc-supply = <&wlreg_on>; + }; + ether_qos@2490000 { vddio_sys_enet_bias-supply = <&battery_reg>; vddio_enet-supply = <&battery_reg>; The above changes must be done on the appropriate dtsi file of ...