1. sd 0:0:0:0: [sda] Assuming drive cache: write through 解决方法:/etc/default/grub 文件里去掉 rhgb 参数,然后执行 grub2-mkconfig -o /boot/grub2/grub.cfg 其中"rhgb"表示"redhat graphics boot",就是图形进度条模式 最后reboot 2. 关机,点击 把已连接按钮取消掉,再重启 但是以上办法我这仍未解...
sd 0:0:0:0: [sda] Assuming drive cache: write through 解决方法:/etc/default/grub 文件里去掉 rhgb 参数,然后执行 grub2-mkconfig -o /boot/grub2/grub.cfg 其中"rhgb"表示"redhat graphics boot",就是图形进度条模式 最后reboot
1. Re:CentOS开机报错:sd 0:0:0:0: [sda] Assuming drive cache: write through 我开机报错 开在背景界面 怎么编辑? 什么都操作不了 --sdok 2. Re:理解tty,pty,pts概念及与描述符的联系 好东西! --3L·BoNuo·Lotus CentOS开机报错:sd 0:0:0:0: [sda] Assuming drive cache: write through 解决...
[ 7.219813] Buffer I/O error on device sda, logical block 0 [ 7.225723] sda: unable to read partition table [ 7.354064] sd 0:0:0:0: [sda] No Caching mode page present [ 7.359808] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 7.366240] sd 0:0:0:0: [sda] Attache...
sda5 [20446.262929] sd 0:0:0:0: rejecting I/O to offline device [20446.262931] Read-error on swap-device (8:0:1520768) [20446.262932] Read-error on swap-device (8:0:1520896) [20446.262932] Read-error on swap-device (8:0:1521024) [20446.264716] sd 0:0:0:0: [sda] CDB: Write(...
if [ ! "$1" = "/dev/sda" ] ; then unset LANG DRIVE=$1 if [ -b "$DRIVE" ] ; then dd if=/dev/zero of=$DRIVE bs=1024 count=1024 SIZE=`fdisk -l $DRIVE | grep Disk | awk '{print $5}'` echo DISK SIZE - $SIZE bytes ...
[sda] 990976 512-byte logical blocks: (507 MB/484 MiB) [ 313.019734] sd 0:0:0:0: [sda] Write Protect is off [ 313.037258] sd 0:0:0:0: [sda] No Caching mode page found [ 313.053771] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 313.089394] sda: sda1 sda2 [...
$ROOTDRIVE to “mask” the volume where “/” is mounted from the selection list using a “grep -v $ROOTDRIVE” For the naive partitioning case, its heuristic is fine, yielding something like “sda” — but for LVM, it grabs some chunk of the device name, ...
Connect the USB drive and uselsblkto figure out its device name. On the Pi I’m using, this is/dev/sda; if yours differs, use its name in place of/dev/sdain the following commands. Runsudo cfdisk /dev/sdaand: Selectgptif prompted to select a partition table type. ...
(in this case “sdb” is the second SATA drive, the first is “sda”; mmcblk1 is the second eMMC/SD, while “mmcblk0” is the first) As a contrast, these are the first partitions of those same devices: /dev/sdb1 /dev/mmcblk1p1 Thanks for the reply. I notice if I dd each...