Win7的USB3.0驱动对所有笔记本安装Win7系统是通用的。 下载到了USB3.0驱动,就要将它注入到有系统安装文件的U盘中(注意不是简单地拷贝进去)。将WIN7_Boot这个文件解压后放到U盘根目录下,直接运行文件夹中的inject_driver.exe即可,完成后按任意键退出即可。这类方式很简单,包括华硕、技嘉都有推出类似直接将驱动注入到...
Intel SATA Controller AHCI Driver for Windows 7 (32-bit, 64-bit), XP - ThinkPad Edge E420, Edge E520
Windows7启动SATA AHCI蓝屏在安装新系统前没有启用SATA AHCI,在系统安装后再启用SATA AHCI,启动系统后,会遭遇蓝屏,且进不了系统. 原因:Win7/Vsita禁用了 AHCI 驱动程序 (Msahci.sys),必须先启用SATA驱动,才能更改成AHCI模式. 要解决此问题,请在更改启动驱动器的 SATA 模式之前在注册表中启用 AHCI 驱动程序.为...
Under Disk Drives, identify the SATA device you would like the inbox driver to consider internal and open properties for this device by right-clicking and selecting Properties. Note the bus number from the properties overview (“1” in the below example). For Windows 7: Type the following com...
When performing a new installation from DVD of Windows 7 or Vista a box will prompt “Where do you want to install Windows?” If the SATA hard drive is not showing then click the Load Driver option. The "additional controller driver" is the SATA controller driver. Whether the SATA c...
1、首先，进入BIOS将硬盘模式改回IDE模式，然后重启系统就不会出现蓝屏了。2、正确的开启ACHI模式的步骤如下：1）、按WIN+R键，打开“运行”对话框，输入regedit按回车键，打开“注册表编辑器”，如果显示“用户帐户控制”对话框，请单击“继续”。2）、找到并单击下面的注册表子项：HKEY_LOCAL_MACHINE...
Use Driver Easy to automatically update your SATA drivers. If you want to make sure your SATA drive works properly on your computer, you shouldkeep your SATA drivers up-to-date. To update your SATA drivers There are two ways you can update yourSATAdrivers inWindows 10,8.1and7:Option 1 –...
During the Windows 7 or Windows Vista installation process, any unused storage drivers are disabled. This behavior speeds up the operating system's startup process. When you change the boot drive to a driver that is disabled, you must enable the new driver...
把下载好的XP SP3镜像用Ultraiso打开把里边全部的文件复制到“F:\zzxp”中,也可使用winRAR解压到该目录下,从现有的Windows XP安装光盘中复制也可以。 2、安装DriverPacks DPs_BASE。硬盘里新建一个目录(如F:\DPs_BASE),运行DPs_BASE_1006.exe,该软件是个7-zip的自解压文件,将该软件解压到F:\DPs_BASE目录下...
For Windows 7: Skriv inn følgende kommando i den tidligere åpnede ledeteksten, og trykk enter: reg.exe legg til "HKLM\SYSTEM\CurrentControlSet\Services\msahci\Controller0\Channelx\" /f /v TreatAsInternalPort /t REG_DWORD /d 0x00000001 ...