SAE J1926/1-2023 购买 正式版 SAE J1926 的这一部分规定了符合 ASME B1.1 标准的带有英制螺纹的流体动力和通用端口的尺寸,用于与 SAE J1926-2、SAE J1926-3 和 SAE J1926 中所示的可调节和不可调节螺柱端部和插头一起使用。 4.符合 SAE J1926 本部分的端口可在工作压力高达 63 MPa(对于不可调节螺柱...
saej1926_1v001美制接头资料 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any ...
NPT和SAE螺纹标准完整版.pdf,® ® SAE STRAIGHT SAE information is provided as an aid to designers. For com- plete specifi cations refer to SAE Standards J1926 for straight THREAD PORT thread ports and J518 JUN93 for 4-Bolt fl ange ports. DIMENSION
161 SAE J2643-2023 2023-05-01 English Standard Reference Elastomers (SREs) for Characterizing the Effect of Liquids on Vulcanized Rubbers 162 SAE AS4329A-2023 2023-05-01 English (R) CAP ASSEMBLY, PRESSURE SEAL, FLARED TUBE FITTING 163 SAE J1926-3-2023 2023-05-01 English Connections for Ge...
本部分定义了用于 SAE J1926-1 端口的 C2 至 C32 内部和外部六角端口插头的性能要求@尺寸@和设计。多年的测试和使用证实了碳钢端口塞的性能要求。 SAE J514 中指定了端口插头,没有任何性能要求。它们经过开发和测试,以获得适合工业应用的 4:1 工作压力等级。在流体动力系统中,动力通过封闭回路内的压力流体(液体...
SAE螺纹标准 SAE STRAIGHT THREAD PORT DIMENSIONS FOR BEST RESULTS USE A FORM TOOL TO MACHINE CAVITY **NOT AN SAE STANDARD. INSERTA TM SAE information is provided as an aid to designers. For com-plete specifi cations refer to SAE Standards J1926 for straight thread ports and J518 JUN93 ...
184 SAE J1453-3-2012 2012-06-01 English (R) Specification for O-Ring Face Seal Connectors: Part 3 - Requirements, Dimensions, and Tests for Steel Unions, Bulkheads, Swivels, Braze Sleeves, Caps, and Connectors with SAE J1926-2 Inch Stud Ends 185 SAE J2296-2012 2012-06-01 English Ret...
& SAE-AMS4342E-2007 Aluminum Alloy,Extrusions (7050-T74511) Solution Heat Treated,Stress Relieved,Straightened,& SAE-AMS4484K-2007 Magnesium Alloy Castings,Permanent Mold (AZ92A-T6) [P7].pdf SAE-AMS4500J-2007 Copper,Sheet,Strip,and Plate Soft Annealed [P4].pdf SAE-AMS4640-2005 ALUMINUM ...
1 SAE AMS4079H-2017 2017-03-01 English Aluminum Alloy, Drawn, Round, Seamless, Tubing 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-O) Close Tolerance, Annealed - UNS A96061 2 SAE J3102-2017 2017-03-01 Eng…
BOSS, GASKET SEAL STRAIGHT THREAD TUBE FITTING, STANDARD DIMENSIONS FOR (SUPERSEDING MS16142B) (S/S BY SAE-J1926/1)doi:MIL MS16142C