M6 到 M36 (3) C33 C39 327 382 1. 如果最小抗拉强度满足要求,最小硬度值不予要求。 2. 5.8 级适用于产品长度≤150mm 的螺栓及螺钉,以及所有长度的螺柱。 3. 表面硬度不得超过多于两点测得的基材硬度(洛氏 C 相当),10.9 级情况下也不得超过 59 HR30N. 4. 对于 9.8 级的螺钉与垫片组件产品,基材...
SAEJ174m-1998 公制钢螺纹紧固件力矩——应力试验规程 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular...
螺钉和螺柱性能等级4.64.85.88.89.810.91.2.3.4公称直径M5至m36m1 6至m16m5至M24(2)M17至m36m1 6至M16(4)最大表面洛氏硬度30n-(3)(3)(3)最小产品洛氏硬度b67b71b82c23c27c33(1)最大产品洛氏硬度b87b95c34c36c39最小产品维氏硬度(1)最大产品维氏硬度180180220336354382120220160254279327m6至M36如果最小抗拉...
M1.6 M2 M2.5 M3 M4 M5 M6 M7 M8 M9 Stainless Steel A2 A4 304 316L DIN 912 Inner Hexagon Shcs Screw Allen Cylindrical Head Socket Head Cap Screw DIN 912 Hexagon Socket Head Cap Screws for Metalwork Professional Wholesale Zkbbs SUS 304 A2-50 Equivalent Low Small Head Cap ...
120 130 160 254 279 327 M6 到 M36 如果最小抗拉强度满足要求,最小硬度值不予要求。 5.8 级适用于产品长度≤150mm 的螺栓及螺钉,以及所有长度的螺柱。 表面硬度不得超过 多于两点测得的基材硬度(洛氏C 相当),10.9 级情况下也不得超过59 HR30N. 对于9.8 级的螺钉与垫片组件产品,基材硬度可在25-40HRC...
6 8 9 10 12 15 18 24 30 36 Y Unthreaded Length Under Head for Nominal Screw Lengths ≤Than 16 20 25 30 35 40 45 45 45 50 Nominal Screw Size and Thread Pitch M2 x 0.4 M2.5 x 0.45 M3 x 0.5 M3.5 x 0.6 M4 x 0.7 M5 x 0.8 M6 x 1 M8 x 1.25 M10 x 1.5 M12 x 1.75 1....
Nut Size M4 x 0.7 M5 x 0.8 M6 x 1.0 Hole Diameter Max 4.38 5.38 6.38 Hole Diameter Min 4.23 5.23 6.23 Nominal Screw and Nut Size M8 x 1.25 M10 x 1.50 M12 x 1.75 Hole Diameter Max 8.41 10.41 12.41 Hole Diameter Min 8.28 10.28 12.28 Hand assemble the test nuts to the test screws....
PARKER M6MSC1/4 N-316 PARKER 06E23A13AC 部件号:254570068 PARKER 06E23B15AC 250PSIG PARKER P0160757 230V 50HZ 4.0V PARKER 序列号:N30045002 PARKER 序列号:N30046004 部件号:254500 PARKER DX3-621-71 PARKER PVM02BR1K8S1NMS PARKER E321F32 DC220V PARKER 4WE6E60/CG24NZ5L PARKER 4WE6Y60...
15、ediment (SAE J 1603, para 6.2, using DOT 4 fluid to SA-M6C9103-A and Super DOT 4 to ESD-M6C57-A) 3.10.4 Brake/Clutch Seal Compatibility, % -0.5 to +1.5 (FLTM BP 121-01, differential seal swell, using DOT 4 fluid to SA-M6C9103-A and Super DOT 4 to ESD-M6C57-A) 5...
15、ibility, %, max 0.05 vol. sediment (SAE J 1603, para 6.2, using DOT 4 fluid to SA-M6C9103-A and Super DOT 4 to ESD-M6C57-A) 3.10.4 Brake/Clutch Seal Compatibility, % -0.5 to +1.5 (FLTM BP 121-01, differential seal swell, using DOT 4 fluid to SA-M6C9103-A and Super...