RTC GPIO 一共有 18 个 IO 口,这些 GPIO 管脚具有低功耗 RTC 性能和模拟功能,并且由 ESP32 的 RTC 子系统控制。这些功能不使用 IO_MUX 和 GPIO 交换矩阵,而是使用 RTC_MUX 将 IO 指向 RTC 子系统。 当这些管脚被配置为 RTC GPIO 管脚时,作为输出的管脚能够在芯片处于 Deep-Sleep 睡眠状态下保持输出电平...
Re: Setting a RTC_GPIO in esp_wake_deep_sleep() PostbyNRollo»Wed Aug 09, 2023 8:56 am I found a solution, this will do the trick: Code: Untitled.cSelect all void RTC_IRAM_ATTR esp_wake_deep_sleep(void) { // Output - set RTC mux ...
As I ran out of normal GPIO's I am trying to use GPIO35 as an output, while normally this is GPI input only pin. I tried this code: Code: Select all rtc_gpio_init(35); rtc_gpio_set_direction(35, RTC_GPIO_MODE_OUTPUT_ONLY); rtc_gpio_set_level(35, 1); It is compiled ...
nrfx_rtc_overflow_disable(&rtc);/* 启用CC通道使能 32768/(4095+1)=0.125ms,那么1s定时为0.125*8,所以设置定时器值是乘以8了,可以自由设置 */err_code= nrf_drv_rtc_cc_set(&rtc,0,handle_tirgg_timer *8,false); APP_ERROR_CHECK(err_code); 2、GPIO口配置为GPIOTE的OUT模式 代码如下: uint32_t...
RTC_GPIO_PINx 寄存器中的RTC_IO_TOUCH_PADx_TO_GPIO 位Quote by helloesp32 » Wed Jul 01, 2020 7:16 am 在技术参考手册中描述RTC GPIO 与 RTC pad之间的连接控制寄存器, 每个pad 的模拟和RTC 功能是由RTC_GPIO_PINx 寄存器中的RTC_IO_TOUCH_PADx_TO_GPIO 位控制的 , 找不到该寄存器的定义和...
之前是没有连接网络设置为2000年1月1日,接上公网后,会自动更新时间并持续写入最新时间到rtc,如下图: 测试GPIO口 AI检测代码解析 sudouno220gpio-hsudouno220gpio--export=allsudouno220gpiosudouno220gpio--in=0--direction=outsudouno220gpio--pin=0--value=1 ...
DM365 RTC GPIO Interrupt 我们在做的项目方案是DM365平台,在应用过程中,由于使用内部网卡,可用中断IO不多,所以使用了RTC GIO 当做外部中断过程中,发现RTC GIO 中断响应很慢,达到毫秒级。根本不可能应用。我的内核是linux 2.6.32 。不知道什么原因会导致上面的情况。现在我不能使用外部中断,没有多余的中断引脚,...
7.1GPIO7.1GPIO实例分析实例分析7.27.2定时器实例分析定时器实例分析7.3RTC7.3RTC实例分析实例分析7.1GPIO7.1GPIO实例分析实例分析GPIOGPIO实..
寻求CC1310驱动(GPIO、RTC) yuandong xia Prodigy52points 你好,我在C:\ti\simplelink_cc13x0_sdk_1_40_00_10\source\ti\drivers下没有找到GPIO.c(但是有GPIO.h),另外没有找到RTC相关驱动。能提供解决途径吗?非常感谢。 8 年多前 Seven Han8 年多前...
Specifications: Protocol Support: MQTT, HTTP, TCP, RS485, Modbus Communication Methods: Bluetooth-compatible, Wi-Fi, Ethernet State of Assembly: Ready-to-Go Compatibility: Arduino IDE, Home Assistant, ESPHome, Tasmota Expansion Capabilities: 12 digital signal inputs, 8 analog outputs, 8 GPIO pins...