rst:0x15 (USB_UART_CHIP_RESET),boot:0x8 (SPI_FAST_FLASH_BOOT) Saved PC:0x4200a463 Any suggestions on where I need to look to either pin this down to a problem with the hardware / PCB layout or the code? ThanksB
Hardware: Board: ESP-WROOM-32(self-assembled board with manual reset) Core Installation/update date: NA IDE name: Arduino IDE 1.8.1 Flash Frequency: 40Mhz Upload Speed: 115200 Description: Sketch Uploading is successful. But when I check...
esptool.py -p /dev/cu.SLAB_USBtoUART write_flash -z 0x1000 ttgocam.bin It uploaded without error Code:Select all esptool.py v2.8Serial port /dev/cu.SLAB_USBtoUART Connecting... Detecting chiptype... ESP32 ChipisESP32D0WDQ5 (revision1) Features: WiFi, BT, Dual Core, 240MHz, ...
rst:0x1 (POWERON_RESET),boot:0x0 (DOWNLOAD_BOOT(UART0/UART1/SDIO_FEI_FEO_V2)) However when the GPIO0 is High and perform a Reset of the Chip I got this message: ␛[0;32mI (10) boot: ESP-IDF v3.0.1 2nd stage bootloader␛[0m ␛[0;32mI (10) boot: compile time 05:26...
rst:0x15 (USB_UART_CHIP_RESET),boot:0x8 (SPI_FAST_FLASH_BOOT) Saved PC:0x4200a463 Any suggestions on where I need to look to either pin this down to a problem with the hardware / PCB layout or the code? ThanksBivvyCoder Posts: 25 Joined: Sun Jan 28, 2024 5:20 pm Re...
Note that as described earlier, certain RTS/DTR sequences lead to hardware reset of ESP32-C6. Software can disable hardware recognition of these DTR/RTS sequences by setting the USB_SERIAL_JTAG_USB_UART_CHIP_RST_DIS bit, allowing software to interpret these signals freely. This is in section...
--- idf_monitor on /dev/cu.SLAB_USBtoUART 115200 --- --- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H --- ets Jun 8 2016 00:22:57 rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv...
use standard USB complete interrupt instead of custom chipidea async/period interrupt to be more compatible with other ehci implementation refactor usb complete & error isr processing, merge, update. Fix EHCI QHD reuses QTD on wrong endpoint Improve bus reset, fix send_setup() not carried out if...
直接下载打包好的量产固件至0x0地址:输入以下命令,替换PORTNAME和FILEDIRECTORY参数; esptool.py --chip auto --port PORTNAME --baud 115200 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 40m --flash_size 4MB 0x0 FILEDIRECTORY ...
I (132) boot_comm: chip revision: 3, min. application chip revision: 1 I (139) esp_image: segment 0: paddr=00010020 vaddr=3f400020 size=3b1d0h (242128) map ��וBets Jul 29 2019 12:21:46 rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) ...