rst:0x10 (rtcwdt_rtc_reset) 是ESP32启动日志中常见的复位原因表示。这里的 rst 表示复位(Reset),而 0x10 是复位原因的代码。rtcwdt_rtc_reset 指的是由实时时钟看门狗(RTC Watchdog Timer)触发的复位。 可能原因: 软件未按时喂狗:在设备长时间处于低功耗模式(如深度睡眠)时,若主
load:0x40080400,len:5816 entry 0x400806ac I was able to resolve this by using the following thread: #1638 Now the current status is rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ...
0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57 rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57 rst:0x10 (RTCWDT_RTC_RESET),boot:...
--- idf_monitor on \\.\COM3 115200 --- --- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H --- ets Jun 8 2016 00:22:57 rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57 rst:0x...
Hello, I got this error and have been searching for an answer but no luck, and not sure if this's the right place to post the question. Please delete or move it if this's not a valid location. Goal: Loading firmware to my custom board us...
Code:Select all voidsetup() { Serial.begin(115200); } voidloop() { Serial.println("Hello");delay(1000); } Just for testing, and i have this error : Code:Select all rst:0x10(RTCWDT_RTC_RESET),boot:0x13(SPI_FAST_FLASH_BOOT)flashreaderr,1000ets_main.c371etsJun82016 00:22:57 ...
6. **RTCWDT重置**：RTCWDT（实时时钟看门狗）可能导致模块重置。您可以尝试关闭RTCWDT功能，或者修改其...
ESP32 烧写microopython后 上电结果反复重启,打印如下: rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57
esp32 的GPIO12/13与4G模块的串口相连,GPIO12为Strapping管脚,上电后由于4G模块的串口的影响,电压为2.5V。对比具体要求: 改变了下拉状态,造成重启。 解决方案: 串口改为 的GPIO14/15后正常。 转:ESP32处于无限重启状态,串口消息rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)-CSDN博客...
This "rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)" problem usually occurs when you use "idf.py -p (PORT) erase-flash" and then try to burn using " idf.py -p (PORT) app-flash" . To fix this problem use "idf.py build" to build the bootloader. ...