rst:0x10 (rtcwdt_rtc_reset) 是ESP32启动日志中常见的复位原因表示。这里的 rst 表示复位(Reset),而 0x10 是复位原因的代码。rtcwdt_rtc_reset 指的是由实时时钟看门狗(RTC Watchdog Timer)触发的复位。 可能原因: 软件未按时喂狗:在设备长时间处于低功耗模式(如深度睡眠)时,若主CPU未能按时重置看门狗计时器...
经查是连接4G模块的串口影响。esp32 的GPIO12/13与4G模块的串口相连,GPIO12为Strapping管脚,上电后由于4G模块的串口的影响,电压为2.5V。对比具体要求: 改变了下拉状态,造成重启。 解决方案: 串口改为 的GPIO14/15后正常。 转:ESP32处于无限重启状态,串口消息rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAS...
57rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57rst:0x10 (RTCWDT_RTC_RESET),boot...
rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57 I already tried to flash the esp32 with factory .bin that i found on https://docs.espressif.com/projects/esp ... aries.html And nothing is connected to GP...
rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57 11:08 rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee rst:0x10 (RTCWDT_RTC_RESET),boot:0x3 (DOWNLOAD_BOOT(UART0/...
ESP32 烧写microopython后 上电结果反复重启,打印如下: rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 ets Jun 8 2016 00:22:57
板子是esp32-wroom，烧写后一直提示 rst:0x10 (RTCWDT_RTC_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT...
rst:0x10(RTCWDT_RTC_RESET),boot:0x13(SPI_FAST_FLASH_BOOT)configsip: 0,SPIWP:0xeeclk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00mode:DIO,clockdiv:2load:0x3f400020,len:277444etsJun8 2016 00:22:57REPEATS... ...
rst:0x10 (..rst:0x10 (RTCWDT_RTC_RESET),boot:0x33 (SPI_FAST_FLASH_BOOT)configsip: 0, SPIWP:0xeeclk_drv:0x00,q_dr
rst:0x10 (RTCWDT_RTC_RESET),boot:0x1f (SPI_FAST_FLASH_BOOT) flash read err, 1000 ets_main.c 371 I am getting this error in my esp32 devkit v1 How to solve it? I am using arduino IDE for programming the esp32. This error went away after I changed esptool.py params to start ...