route loop-detect ospf disable命令用来去使能OSPF引入路由环路检测功能。 缺省情况下,去使能OSPF引入路由环路检测功能。 命令格式 route loop-detect ospf disable 参数说明 无 视图 系统视图 缺省级别 2:配置级 任务名称和操作类型 任务名称操作类型 ospf write 使用指南 该命令是升级兼容命令,仅在配置恢
The route loop-detect ospf disable command disables loop detection for routes imported into OSPF. By default, loop detection is disabled for routes imported into OSPF. Format route loop-detect ospf disable Parameters None Views System view Default Level 2: Configuration level Task Name and Op...
ospf prefix-suppression [ disable ] 缺省情况下,不抑制接口进行前缀发布 1.7.21 配置OSPF的前缀按优先权收敛功能 通过策略指定优先权,不同前缀按优先权顺序下发,由高到低分为4个优先权(Critical、High、Medium和Low),如果一条路由符合多个收敛优先权的匹配规则,则这些收敛优先权中最高者当选为路由的收敛优先权...
1.MTU:OSPF协议会在DBD包中携带与邻居直连接口的MTU值,要求邻居的MTU值必须完全一致,否则将卡在exstart状态机,默认华为设备间不检测这个MTU值。 [R1]int g0/0/1 [R1-g0/0/1]ospf mtu-enable 在于邻居间直连的接口上开启MTU检测,若一端开启,另一端也必须开启 2.隐形确认:一台设备使用和另一台设备一样的...
E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route Gateway of last resort is 10.0.0.1 to network 0.0....
This protocol is defined by two IETF drafts, the purpose of which is to allow a given device the ability to detect whether the path to the next router is valid in both directions. This protocol needs to be implemented on both ends of a physical link and is specific to that link only....
以下路由器A的OSPF route id 是多少( )。 Router A: loopback0 10.1.1.1 E0 10.2.2.2 E1 10.3.3.3 S0 10.4.4.4A.10.4.4.4B.10.3.3.3C.10.2.2.2D.10.1.1.1的答案是什么.用刷刷题APP,拍照搜索答疑.刷刷题(shuashuati.com)是专业的大学职业搜题找答案,刷题练习的工具.一键将文
更多“在R2的showiprouteospf中,关于R1的loopback0的路由条目下一跳指向哪个路由器。”相关的问题 第1题 YoureplacedyourLayer3switch,whichisthedefaultgatewayoftheendusers.Manyuserscannotaccessany thingnow,includingemail,Internet,andotherapplications,althoughotherusersdonothaveanyissues.Alloftheapplicationsare...
OSPF Router ID 的选取遵循以下规则:1. **手动配置的Router ID**优先;2. 若无手动配置,则选择**最大的loopback接口IP地址**;3. 无loopback接口时,选择**活动物理接口中最大的IP地址**。**选项分析**:- **A. 物理接口的最小IP地址**:错误。OSPF在无loopback时选择最大物理接口IP,而非最小。- **...
The question then is: can we detect and avoid routing loops? The answer is yes, but the solution requires two additional attributes as described below: • ORIGINATOR–ID: This attribute identifies a route reflector through its 4-byte router ID; it is given the type code 9, and is ...