1.3 Boot 过程 由于主内存是易失性的,因此无论何时打开计算机电源,它都仅仅包含一堆垃圾。 因此,此时 CPU 可能无法从主内存中检索指令。 在这种情况下,打开电源时,PC 会自动设置为 CPU 通过从一个小型非易失性内存设备中检索指令来启动,该内存设备存储了一个执行boot process的小程序(注4)。 该程序设置基本的...
对于嵌入式SOC(System On Chip)芯片来说,芯片内本身含有SRAM用于将闪存中的bootloader(uboot)加载到RAM来运行,但由于片内RAM大小限制,加载不了完整的U-boot程序,所以需要在片外的RAM上运行完整的Uboot。 作为bootloader的第一阶段FSBL(First Stage Boot Loader),BOOT0从启动日志上可以看出一些它的功能:打开倍频统一...
fw_payload_oe_docker.elf利用 openSBI 将 kernel-5.5 的 image 作为 payload 所制作的用于 QEMU 启动的 image,同时它也增加了 Docker 相关的启动配置。 openEuler-preview.riscv64.qcow2openEuler RISC-V 移植版的 rootfs 镜像。 通过QEMU 启动一个 openEuler RISC-V 首先你需要在你的 Host Linux 环境中有 qem...
kernel main函数执行的流程中,会在这里初始化pid=1的内核线程:https://code.dragonos.org.cn/xref/DragonOS/kernel/src/process/kthread.rs?r=f0c87a897fe813b7f06bf5a9e93c43ad9519dafd#266接着,在这个函数之后,启用了中断,随着时钟中断的到来(或者是因为arch_idle_func里面手动执行调度),就会切换到initial_...
boot.c: the original C code for the boot process boot.s: the assembler version of the C code, generated automatically by the gcc boot.o: the compiled version of the C code, generated automatically by the gccWhen all .o files are produced, the result is linked in a darksocv.o ELF ...
U-Boot:U-Boot-2018.07 Kernel:Linux-5.4.61、Linux-RT-5.4.61 LinuxSDK:T113_Tina5.0-V1.0(Linux) OpenAMP简介 AMP(Asymmetric Multi-Processing),即非对称多处理架构。“非对称AMP”双系统是指多个核心相对独立运行不同的操作系统或裸机应用程序,如Linux +RTOS/裸机,但需一个主核心来控制整个系统以及其它从...
所谓软件中断就是软件触发的中断,也是所谓的核间中断(inter-process interrupt,IPI)。在 RISC v 中,核间中断是通过设置 MIP 的 MSIP 或者 SSIP 实现的。 下面以 Linux 和 opensbi 为例介绍 S-MODE 的软件中断的实现。 回到顶部 中断发送# Linux 内核实现# ...
I remember when disabling cache support on Linux kernel the boot process was really slow. Normally we don't pay too much attention on it on NuttX because it always boot in milliseconds even when cache is disabled. So this kind of benchmark, comparison is very important. I think we need ...
copy_process-->dup_task_struct setup_sigcontext-->save_fp_state switch_to-->__switch_to_aux fstate_save--如果SR_FS为SR_FS_DIRTY,则保存上下文。__fstate_save li t1, SR_FS csrs CSR_STATUS, t1--打开FP功能。...--保存fcsr、f0-f31寄存器。csrc CSR_STATUS, t1--关闭FP功能。compat_restor...
If there are no problems, an ash prompt will appear after the boot process completes. It will be pretty useless without the usual plethora of command-line utilities, but you can add them as BusyBox applets. Have fun!To exit the simulator, hit Ctrl-C....