1、raspi-config配置 如果需要更改树莓派的配置,可通过自带的脚本工具raspi-config来完成,这个工具很重要,它直接有效,非常方便。 # sudo raspi-config raspi-config配置界面 (1)启动摄像头模块 在raspi-config图形配置界面中,依次选择【Interfacing Options】-【Camera】-【Enable】,确认完成启用摄像头的配置后,重启...
lsmod 其实就是list modules的缩写,即 列出所有模块.6:eth0:是第一块网卡,wlan0是第一块无线网卡,配置无线网卡使用iwconfig 查看网卡信息使用ifconfig 包括IP地址,mac地址等7:nano 编辑文本8:重启网络: Debian Linux command to reload or restart network: #/etc/init.d/networking restart To start Linux netwo...
具体教程网上也是有很多的,记得一点是raspberry默认SSH是DISABLE的,需要通过sudo raspi-config来开启,不然是连接不上的。 之后我就想用下真正的远程桌面了,网上也是有很多的教程,特别的简单,但是我在安装xrdp的时候一直提示连接不上,不能成功安装。 pi@raspberrypi:/ $ sudo apt-get install xrdp Reading package l...
Using the Pi with a displayIf you boot to the command line instead of the desktop, your IP address should be shown in the last few messages before the login prompt.Using the terminal (boot to the command line or open a Terminal window from the desktop), simply type hostname -I which ...
raspberry pi买回来玩了一段时间,现在就记录一下入门遇到的一些问题吧。 首先是烧写镜像,和安装电脑系统是一样的道理。 先要有一个制作一个U启动盘。先将SD卡格式化,再用Win32DiskImager或dd命令将raspberry官方下载的镜像烧写进去(这种文档很多的,随便找一个都可以完成操作)。
Raspi-config is a great tool you can use from your Raspberry Pi directly, but also when connected by SSH. It allows you to configure many system options with a simple interface. Are you a bit lost in the Linux command line? Check this article first for the most important commands to re...
开机,使用sudo raspi-config,选择interfacing opinions,选择Camera,并Enable Finish退出配置 重启 二、使用命令控制摄像头 如果一切顺利的话,就可以使用命令控制摄像头了 拍照---raspistill 拍摄一张照片,保存在桌面,命名为image.jpg,等待几秒后,桌面就会出现jpg文件 ...
简介:raspberry pi买回来玩了一段时间,现在就记录一下入门遇到的一些问题吧。 首先是烧写镜像,和安装电脑系统是一样的道理。 先要有一个制作一个U启动盘。先将SD卡格式化,再用Win32DiskImager或dd命令将raspberry官方下载的镜像烧写进去(这种文档很多的,随便找一个都可以完成操作)。
On your Raspberry Pi, run the commandvncserver-virtual Make a note of the IP address/display number printed to the console, for example192.167.5.149:1 On the device you will use to take control, enter this information in RealVNC Viewer. ...
Are you a bit lost in the Linux command line?Check this article firstfor the most important commands to remember and a free downloadable cheat sheet so you can have the commands at your fingertips. 4: config.txt Another method you can try is to edit the Raspberry Pi OS configuration file...