选择要配置的Array级别“RAID5”,并选择“Proceed to next Form”。 进入Array属性配置界面,如图11-102所示,参数说明如表11-20所示。 图11-102配置Array属性 表11-20参数说明 参数 说明 Logical Drive Label LD的自定义标签。 Strip Size/Full Stripe Size ...
选择要配置的Array级别“RAID1”,并选择“Proceed to next Form”。 进入Array属性配置界面,如图17-90所示,参数说明如表17-17所示。 图17-90配置Array属性 表17-17参数说明 参数 说明 Logical Drive Label LD的自定义标签。 Strip Size/Full Stripe Size ...
3）选择 Create Array，按 Enter。4）选择要使用的磁盘（Enabled 表示选中），然后选择[Proceed to next Form]，按 Enter。5）在 RAIDLevel 一栏设置 RAID 级别，然后选择[Proceed to next Form]，按 Enter。6）在 Logical Drive Label、Stripe Size/Full Stripe Size、Size、Unit Size 和 AccelerationMethod 栏...
Unconfig good: Good but need to rebuild. In case of one failed disk was found, replace the failed disk and execute Rebuild Scan Disk Array in Reconfig menu. (The menu is displayed just in case of one disk is "Unconfig good" status.) Scan fil...
Open the RAID Recovery™ application, if you need automatic mode, activate the wizards, then be sure to select the target array. Then decide on the priority recovery mode: Quick recovery mode (try it first, it will be fast). Full recovery mode (deeper scan and the results will be much...
Size is specified as an amount per second for each device in the array. If no suffix is given, then KiB/sec/device is used. Setting the recovery rate to 0 means it will be unbounded. --minrecoveryrate Size[k|UNIT] Sets the minimum recovery rate for a RAID LV. Size is specified as...
选择create array将要做RAID0的硬盘enable,点击proceed to next formRAID级别选择RAID0,点击proceed to next form依次配置阵列名称、条带值、阵列大小、加速策略,设置成功后选择submit changes参数说明Logical Drive LabelLD的自定义标签。Strip Size/Full Stripe SizeStrip Size:单个物理盘的条带大小,可设置为16KiB/32...
独立硬盘冗余阵列(RAID, Redundant Array of Independent Disks),旧称廉价磁盘冗余阵列(Redundant Array of Inexpensive Disks),简称磁盘阵列。其基本思想就是把多个相对便宜的硬盘组合起来,成为一个硬盘阵列组,使性能达到甚至超过一个价格昂贵、容量巨大的硬盘。根据选择的版本不同,RAID比单颗硬盘有以下一个或多个方面...
Sets the minimum recovery rate for a RAID LV.Sizeis specified as an amount per second for each device in the array. If no suffix is given, then KiB/sec/device is used. Setting the recovery rate to0means it will be unbounded.
进入图6-10所示界面,选择Create Array,按Enter。 图6-10 Array Configuration界面 进入图6-11所示界面,选择要使用的磁盘(Enabled表示选中),然后选择[Proceed to Form],按Enter。 图6-11 选择磁盘 进入图6-12所示界面,在RAID Level一栏设置RAID级别,然后选择[Proceed to next Form],按Enter。 图6-12 设置RAID...