For example, for the ISO7320FC, if 5V is used for VCC1 and VCC2 with a 25Mbps input signal, the maximum current would be 2.3mA on VCC1 and 6.8mA on VCC2. If a different supply voltage, data rate, or load is used this value can vary. ...
microprocessor, from a power supply (Vcc) during exceeding of threshold temperature, where a plastic housing (3) is provided for accommodating the electronic circuit. The electronic circuit is connected with the power supply during exceeding of another threshold temperature, which is smaller than the...
VCC regulator - VCC LDO output voltage SWO VBIAS threshold (3 V< VBIAS < 5.5 V) VBIAS = GND (no switchover) VBIAS = 5 V (switchover) Switch internal supply from VIN to VBIAS Switch internal supply from VBIAS to VIN - 4 - 38 - 2.7 - 3.5 V - 2.4 - 3.5 - 0.8 - - - 0.65 ...
No external load is expected on VCC pin. The switchover function is enabled in case VBIAS is detected higher than the SWO threshold (refer to Table 7). When this occurs, the internal LDO power supply is switched from VIN to VBIAS, so increasing the power conversion efficiency. This is ...
Supply Current uA No.of Voltage Monitors Fixed Reset Threshold (V) Reset Output Type Manual Reset Enable Reset Timeout Period (ms) Status min max CXDC6598 /A/B STB COMM Portable General SOT23 SOT25 SOT89 1.RESET 2.VCC 3.GND 1.2 5.5 1.5 1 1.5/1.75 2.32/2.63 2.93/3.08 3.9/...
aThe VCC pin connection circuitry and the power supply flow-chart is shown in Figure 10. When AC[translate] aA hybrid model of a boiler developed with the application of both analytical modelling and artificial intelligence is described 锅炉的一个混合模型开发以分析模型和人工智能的应用被描述[transla...
The other end of the relay KA1 coil and the cathode of the diode D1 are connected with the input voltage +Vcc of the power supply. The drive master control circuit comprises an OR-NOT circuit HEF4001BT, an integrating circuit and a differentiating circuit. The central controller is low ...
(3) eN Output noise voltage SVR Supply voltage rejection IQ Quiescent current Test conditions Device On Minimum input voltage for regulation (1) VOUT + 1 V (2) < VIN < 18 V, 0.1 mA < IOUT < 400 mA, -40 °C < TJ < 125 °C TJ = 25 °C VOUT + 1 V (2) < VIN < 18 V...
(VCC) VVCC Supply voltage 2.7 Shutdown supply current VEN = 0 V 0.2 Standby supply current VEN = 3.3 V, Chip_EN = 0 (bit) 6 IVCC Normal-mode supply current With 10-mA LED current per OUTx Power-save mode supply current VEN = 3.3 V, Chip_EN = 1 (bit), Power_Save_EN = 1 ...
MR Threshold vs Temperature VCC = 1.5 V VCC = 3.3 V VCC = 5.5 V 400 300 200 100 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 VDD (V) D004 MR = 0 V Figure 9. Supply Current vs Power-Supply Voltage 3 2.75 VIL VIH 2.5 2.25 2 1.75 1.5 1.25 1 -50 -25 0 25 50 Temperature ...