我正在使用 iLLD,并尝试使用不同的方法来更改 CS。 通常情况下,每个设备都有自己的配置结构,当我为特定设备调用IfxQspi_SpiMaster_write 时,CS 应自动更改,但不知何故,它不想更改。 到目前为止行之有效的方法: -使用 IfxQspi_setSlaveSelectOutputControl 启用所需的 SLSO -使用 IfxQspi_writeBasic...
IfxQspi_SlaveConfig slaveConfig2 = { .sso = IfxQspi_Sso_4, .csPolarity = IfxQspi_CsPolarity_activeLow }; ``` 3. 设置 SLSO 控制:使用 `IfxQspi_setSlaveSelectOutputControl` 函数启用所需的 SLSO。例如: ```c IfxQspi_setSlaveSelectOutputControl(&MODULE_QSPI1, IfxQspi_Sso_3, TRUE); ```...
Flash Programmer を CodeWarrior の JTAG と一緒に使おうとしていますが、QSPI 信号が機能しません。 具体的には、起動直後にQSPI_A_CS0信号がHighからLowに遷移しますが、Flash Programmerの起動後にCSが応答しません。 フラッシュ プログラマからの QSPI の消去とダ...
-using IfxQspi_setSlaveSelectOutputControl to enable the desired SLSO -using IfxQspi_writeBasicConfigurationEndStream followed by a dummy write to push the TxFiFo and update the registers -manually changing the QSPI1.BACON.B.CS register via BACONENTRY None of the options work, at this point...
However, when the QSPI controller Manual_CS is set to auto mode and BAUD_RATE_DIV is divide by 2, it only reports the status of the lower device. Therefore, the status is incorrect if the lower memory is ready and upper memory is still busy. This is a third-party errata; this issue...
人物简介: 一、张炳厚担任职务:张炳厚目前担任天津市武清区记忆民族文化博物馆法定代表人;二、张炳厚投资情况:目前张炳厚投资天津市武清区记忆民族文化博物馆最终收益股份为0%;老板履历 图文概览商业履历 任职全景图 投资、任职的关联公司 商业关系图 一图看清商业版图 ...
After the LS1046A boots up, the QSPI CS is always in a LOW state.Options SOLVED Jump to solution 02-21-2025 12:31 AM 230 Views Johnson_s Contributor III そのLS1046Aを実装したオリジナルボードを作成しました。Flash Programmer を CodeWarrio...
人物简介: 一、李小燕担任职务:李小燕目前担任日照市东港区朗思读书社(个体工商户)法定代表人;二、李小燕投资情况:目前李小燕投资日照市东港区朗思读书社(个体工商户)最终收益股份为0%;老板履历 图文概览商业履历 任职全景图 投资、任职的关联公司 商业关系图 一图看清商业版图 ...
Even though I set the QSPI0_SSOC.B.OEN register to 0x0 with reference to other subscriptions, CS works automatically still. To check one thing, I set the CS pin in the init function to pinState setHigh in the in state, and even though the test was carried out, the pinState...