Router（config）#int f0/1 Router（config-if）#service-policy input test01 3.限制后效果。一、网络说明user1_PC1接在Cisco3560 F0/1上，速率为1Ｍ；ip_add 192.168.1.1/24user2_PC2接在Cisco3560 F0/2上，速率为2Ｍ；ip_add 192.168.2.1/24Cisco3560的G0/1为出口,或级联端口。二、...
Cisco(config-route-map)#exit Cisco(config)#class-map match-anyNORMAL Cisco(config-cmap)#match ip precedence 0 1 2 Cisco(config-cmap)#class-map match-anyPREMIUM Cisco(config-cmap)#match ip precedence 0 1 2 Cisco(config-cmap)#exit Cisco(config)#policy-mapQoS_OUTPUT Cisco(config-pmap)#class...
I used the media converter between my WAN Router & Carrier Equipment, Duplex mismatch was between Media Converter to my Carrier Equipment( I did not have any visibility in terms of Error etc..) . I could not see any input or output errors on my Router because my router to media...
在Router1的FastEthernet介面,Marking-For-FTP原則會套用到FTP封包,且封包會使用DSCP值AF11標籤。 標籤的FTP資料包通過Router1上的串列介面s3/0和Router2上的S0/0。在此處,將根據WRED配置的閾值檢查資料包的丟棄概率。當平均隊列長度達到最小閾值(對於FTP資料包,為30個資料包)時,WRED隨機丟棄某些具有DSCP值AF11的...
hostname Router1 ! ! ip subnet-zero ! ! ! call rsvp-sync ! ! class-map match-all FTP !--- Classifies FTP Packets based on Access List 103. match access-group 103 class-map match-all Video !--- Classifies Video Packets based on Access List 102. match access-group 102 class-map ...
问。 service-policy is supported only on VIP interfaces with DCEF enabled 消息意味着什么? A. 在仅通用接口处理器(VIP)在一个Cisco 7500系列,分布式服务质量(QoS)功能自Cisco IOS 12.1(5)T、12.1(5)E和12.0(14)S请是支持的。 启用Distributed Cisco Express Forwarding (DCEF)自动地启用分布式QOS。 Non...
Cisco(config)#route-map QoS permit10Cisco(config-route-map)#match ip address BOSS Cisco(config-route-map)#setip precedence ? <0-7>Precedence value critical Set critical precedence (5) flash Set flash precedence (3) flash-overrideSet flashoverrideprecedence (4) ...
On simple Linksys routers with standard firmware you should typically see three types of QoS settings: Device Priority, Ethernet Port Priority, and Application Priority. The information below is for typical Cisco/Linksys routers. For a open source firmware that can be flashed on some older Linksys...
But, when I compare with my other plugin for Nagios which display the traffic in and out of my router I see that the traffic of my qos is just for the traffic_out. I'm more interested in knowing what is the qos' traffic of my router for the traffic_in! If there is another OID...
router-id 22.1.1.1 exit int s2/1 encapsulation frame-relay no shut exit int s2/1.1 point-to-point ip add 24.1.1.2 255.255.255.0 frame-relay interface-dlci 204 exit ip ospf 1 area 0 exit int f1/0 ip add 24.1.2.2 255.255.255.0