qos burst-mode命令用来配置设备缓存管理的突发模式。 undo qos burst-mode命令用来恢复设备缓存管理的突发模式为缺省模式。 缺省情况下,CX320缓存管理的突发模式为标准模式。 命令格式 qos burst-mode { enhanced | shared } slot slot-id undo qos burst-mode { enhanced | shared } slot slot-id 参数说明 参...
qos burst-mode命令用来配置接口下缓存管理的突发模式。 undo qos burst-mode命令用来恢复接口下缓存管理的突发模式为缺省模式。 缺省情况下,CX320接口下缓存管理的突发模式为标准模式。 命令格式 qos burst-mode{enhanced|shared} undo qos burst-mode{enhanced|shared} ...
开启Burst功能 burst-mode enable 缺省情况下,Burst功能处于关闭状态 1.2.2 手工配置数据缓冲区 · 数据缓冲区的配置比较复杂,而且对设备的转发功能有重要的影响,建议用户不要轻易修改数据缓冲区的缺省参数。在需要较大的缓存空间时,建议使用Burst功能来自动分配缓冲区。 · 对于packet资源,本系列设备只支持配置指定队...
[Sysname] buffer egress slot 2 cell total-shared ratio 65 1.1.5 burst-mode enable burst-mode enable命令用来开启Burst功能。 undo burst-mode enable命令用来关闭Burst功能。 【命令】 burst-mode enable undo burst-mode enable 【缺省情况】 Burst功能处于关闭状态。 【视图】 系统视图 【缺省用户角色】 net...
步骤3 通过以下任一方法降低接口上的突发流量: l 在接口上执行qos burst-mode { enhanced | extreme }命令修改接口上缓存管理的突 发模式为增强模式。 l 在接口上执行qos queue queue-index buffer shared-ratio ratio-value命令调大接口上 队列占用动态缓存的最大百分比。 l 通过eth-trunk trunk-id [ mode {...
To attach a shared policy instance to multiple subinterfaces: Enter interface configuration mode and configure a subinterface. Attach a policy map to an input or output subinterface for it to be the service policy for that subinterface. RP/0/RP0/CPU0:router(config)#interface...
shared-policer-per-class-stats No No None ipv6_short No No None qos_ipv6_short_etm_profile Yes Yes None short_l2qos_enable No No None l2_match_dest_addr_v4v6 No No None stats qos_enhanced No No None free-buffer-int-threshold No No None qosg-dscp-mark-enable Yes...
qos carl carl-index {precedence precedence-value | mac-address | dscp dscp-list | {destination-ip-address | source-ip-address} [per-address [shared-bandwidth] ]} -在接口应用基于CARL或ACL的CAR原则: qos car{inbound | outbound} {any | acl [ipv6]acl-number |carlcarl-index}circommitted-inf...
Policer也有MBS参数,在作用上相当于queue的MBS参数,但它不是buffer size的概念,而是burst size的概念。 queue在创建时有下面优先级参数: <queue-type> : expedite|best-effort|auto-expedite <queue-mode> : profile-mode|priority-mode “queue-type“关系到queue被调度的优先级,”queue-mode“关系到packet的profi...
Note that in Shape Mode, the PeakBandwidth interacts with the pipe's MTU size in the following manner: the PeakBandwidth limits the maximum rate at which packets may be burst onto the network. If the TokenBucketSize is equal to the pipe's MTU size and the applica...