执行命令qos burst-mode{enhanced|extreme}slotslot-id,配置单板缓存管理的突发模式。配置突发模式为极限模式,可能会影响到其它接口的正常转发功能,因此建议配置接口管理的突发模式为增强模式。 LE1D2S04SEC0单板、X1C系列单板、X1L系列单板、X1E系列单板、BC系列单板、SA系列单板(LE0DX12XSA00单板除外)、X5E系列单板...
qos burst-mode命令用来配置设备缓存管理的突发模式。 undo qos burst-mode命令用来恢复设备缓存管理的突发模式为缺省模式。 缺省情况下,设备缓存管理的突发模式为标准模式。 命令格式 qos burst-mode { enhanced | extreme } slot slot-id undo qos burst-mode { enhanced | extreme } slot slot-id 参数说明 参...
步骤3 通过以下任一方法降低接口上的突发流量: l 在接口上执行qos burst-mode { enhanced | extreme }命令修改接口上缓存管理的突 发模式为增强模式。 l 在接口上执行qos queue queue-index buffer shared-ratio ratio-value命令调大接口上 队列占用动态缓存的最大百分比。 l 通过eth-trunk trunk-id [ mode {...
Mode QoS PolicyMap Configuration Default class - 0 Example SEFOS(config-ply-map)# set policy class 1 interface extreme-ethernet 0/1 default-priority-type none Notes CLASS must have been created. Related Commandsclass-map - Adds a class map entry policy-map - Creates a policy map...
Q. Is it possible to implement time-of-day-based QoS—specifically, to modify the maximum and burst rates—through Cisco IOS software on the Multilayer Switch Feature Card (MSFC) in hybrid mode? If possible, is this QoS done in hardware and not by the MSFC processor?
In the extreme case, the number of stations in this subset can be reduced to one as it is in LBP. But the only leader may be not enough to provide reliable multicast and thus, to meet QoS requirements for all multicast recipients. To not rely on the only leader, ELBP uses several ...
在接口上执行qos burst-mode{enhanced|extreme}命令修改接口上缓存管理的突发模式为增强模式。 通过eth-trunktrunk-id[mode{active|passive} ]命令将接口加入Eth-Trunk,扩大接口带宽。 在接口上执行display qos queue statisticsinterfaceinterface-typeinterface-number[queuequeue-index]命令查看是否出现丢包,或间隔一小时后...
qos burst-mode{enhanced|extreme} 配置接口缓存管理的突发模式。 进入系统视图。 system-view 进入接口视图。 interface{interface-typeinterface-number|interface-name} 配置缓存管理的突发模式。 对于S8700-4的SRUDX1系列主控板、S8700-6的SRUEX1系列主控板、S8700-10的SRUFX1系列主控板: ...
在转发设备发生拥塞时,可以在发生拥塞的接口下执行qos burst-mode{enhanced|extreme}命令配置接口下缓存管理的突发模式为增强模式,以尝试缓解网络拥塞。 在延时可控和缓存充足的情况下,在发生拥塞的转发设备的上游交换机下行接口通过qos queuequeue-indexshapingcircir-valuepirpir-value[cbscbs-valuepbspbs-value]命令开启...
The qos burst-mode command configures the burst traffic buffering mode on a switch. The undo qos burst-mode command restores the default burst traffic buffering mode on a switch. The default burst traffic buffering mode on a switch is standard. Format qos burst-mode { enhanced | extreme } s...