DefaultRouterIPAddresses11 AccessingtheRouterUsingaBrowser11 AccessingtheRouterUsingQfinderPro12 3.BasicOperations LEDs13 ResetButton14 4.QuRouter AboutQuRouter15 SystemRequirements15 GettingStarted15 ConfiguringQuRouter16 BindingtheRouterwithaQNAPID17 ...
5 为虚拟交换机选择使用动态、静态或无IP地址。若要在虚拟交换机上启用NAT或DHCP，必须使用静态IP。若要使用静态IP，需要选择与另一适配器相同的网络设置，或填写Fixed IP Address（固定IP地址）、Subnet Mask（子网掩码）和Default Gateway（默认网关）字段手动输入网络信息。选择动态IP后，选择下一步 6 设置动态IP...
MIS_GP1DIR[1801b104] default=0x040000a8 [should be 0x1801b104,0x04000028] MUXPAD3[1800036c] default=0x00155049 [should be 0x1800036c,0x10025555] CRT_MUXPAD1[18000364] default=0x00000000 [should be 0x18000364,0x00000000] MIS_GP0DATO[1801b110] default=0x00000000 [should be 0x1801b110,0x...
#备用带宽设置:最大上传带宽 "bind-address-ipv4": "0.0.0.0", "bind-address-ipv6": "::", "blocklist-enabled": true, "blocklist-url": " "cache-size-mb": 4, #缓存大小,默认是4M,我找不到相关的修改资料,根据经验自己修改为了32M,通常而言,这个值大一点对硬盘健康有好处,但一般不要超过磁盘...
"bind-address-ipv4": "0.0.0.0", # IPv4 地址绑定,一般不要改动 "bind-address-ipv6": "::", #IPv6 地址绑定,一般不要改动 "blocklist-enabled": false, # 启动白名单,默认不启动,需要启动改为 true "blocklist-url": "http://www.example.com/blocklist", ...
QNAP NAS FTP settings in PhotoSync 1200 out of 2231 found this article helpful Was this article helpful?Yes|No Go back Need more support?
"bind-address-ipv4": "0.0.0.0", "bind-address-ipv6": "::", "blocklist-enabled": true, "blocklist-url": "<a href="http://www.bluetack.co.uk/config/level1.gz"," rel="nofollow">http://www.bluetack.co.uk/config/level1.gz",</a> "cache-size-mb": 4, #缓存大小,默认...
5.Locatetheswitchinthelistandthendouble-clickthenameorIPaddress. TheQSSloginscreenappears, 6.LogintoQS5, TheQSSdefaultlogindetailsareasfollows: ,Username:admin ,Password:admin TheWelcomewindowappears. 7.Specifythefollowinginformation, ,NASname:Specifyanamewith1to14characters,Thenamesupportsletters(AtoZ,ato...
What is the ip address shown in QFinder? If it is this pattern: 169.254. x.y, where x and y are any two numbers between 0 and 255. That means the QNAP couldn't get an address from the DHCP server when you did the 3 second reset, so it assigned the above default IP address. ...
Access the remote site machine to set the remote site IP (it cannot be identical to the local site IP; the default IP segment on the LAN side is 192.168.100.1, you can change the remote default IP to 192.168.200.1 segment). Repeat steps 1-3 at the remote site. Complete th...