vrrp6 vrid preempt timer delay命令用来配置VRRP6备份组中设备的抢占延迟时间。 undo vrrp6 vrid preempt timer delay命令用来恢复VRRP6备份组中设备的抢占延迟时间为缺省值。 缺省情况下,VRRP6备份组中设备因接口状态Up导致抢占的抢占延迟时间为5秒,其他原因导致抢占的抢占延迟时间为0秒,即立即抢占。
vrrp vrid preempt-mode timer delay命令用来配置VRRP备份组中无线接入控制器的抢占延迟时间。 undo vrrp vrid preempt-mode timer delay命令用来恢复配置VRRP备份组中无线接入控制器的抢占延迟时间为缺省值。 缺省情况下,抢占延时为0,即立即抢占。 命令格式 ...
5. 解释timer delay 20参数在vrrp配置中的具体作用 timer delay 20参数在VRRP配置中用于设置抢占延迟时间。当preempt-mode被启用时,如果备份路由器的优先级高于当前主路由器,并且满足其他抢占条件(如主路由器优先级变为0或低于备份路由器),备份路由器不会立即成为新的主路由器,而是会等待指定的延迟时间(在这个例子中...
配置VRRP抢占时延的命令是: A. Vrrpvrid1preempt-timer20 B. Vrrpvrid1preempt-modetimerdelay20 C. V
Vrrpvrid1timerdelay20 D. Vrrpvrid1preempt-delay20 答案 B答案:B解析:配置VRRP抢占时延的正确命令是:vrrpvrid1preempt-modetimerdelay20。相关推荐 1配置VRRP抢占时延的命令是: A. Vrrpvrid1preempt-timer20 B. Vrrpvrid1preempt-modetimerdelay20 C. Vrrpvrid1timerdelay20 D. Vrrpvrid1preempt-delay20 ...
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0[ 0.000000] GICv3: GIC: Using split EOI/Deactivate...
SolarEdge AM64x_SBL version 0.0.6.Compiled on Aug 29 2023 10:46:11. --- Boot-mode enabled, Entering Bootloading process... R5_0_0 Validation AppStartAddress = 0x0 AppEndAddress = 0x695c0 memBaseAddress = 0x0 version sizes valid
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 224 SPIs implemented ...
will trigger the auto-analysis mode ▶ A threshold is set with -a ▶ Measurement will stop if a latency higher than the threshold is detected ▶ Timerlat then prints a stack trace with the cause of the latency ▶ Can identify if the latency comes from a blocking or an interference...
arm64: dts: ti: k3-j7200-main: Add Itap Delay Value For DDR52 speed mode arm64: dts: ti: k3-j721s2-main: Add Itap Delay Value For DDR50 speed mode arm64: dts: ti: k3-j784s4-main: Add Itap Delay Value For DDR50 speed mode arm64: dts: ti: k3-j721s2-main: Enable ...