PPS信号的生成和输出:除了作为PPS信号的消费者,PPS-GPIO也可以用于生成PPS信号。有些项目,如pps-gen-gpio,提供了通过GPIO引脚生成PPS信号的功能,这在测试和模拟PPS信号时非常有用。 module_platform_driver pps_gpio_driver pps_gpio_probe pps_gpio_setup--根据dts配置获取
1. kernel timer client 是内核软件模拟的pps信号,用于测试 2. pps client using gpio 是以gpio作为pps信号源 pps-gpio.c源码实现也比较简单,主要通过注册gpio中断,当gpio电平变化时,记录当前系统运行时刻,然后post event到用户空间。 因为使用了外部GPIO,因此在使用该模块之前,需要在dts中指定相关的gpio引脚,compati...
I'm trying to connect a GPS 1PPS signal to a FRWY-LS1046 via a GPIO line. I've done the following: Kernel config: CONFIG_PPS=y CONFIG_PPS_CLIENT_GPIO=m CONFIG_PPS_DEBUG=y fsl-ls1046a.dtsi: pps { compatible = "pps-gpio"; gpios = <&gpio3 11 0>; assert-falling-edge; }; ...
Hi, We are trying to use IRQ04/GPIO3_28 pin for PPS. This pin is connected to FPGA which generates PPS. We have enabled PPS driver in the kernel
pps-gen { pinctrl-names = "default"; pinctrl-0 = <&pps_gen_pins>; compatible = "pps-gen-gpio"; pps-gen-gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>; default-state = "off"; Please note that in order to use the module with any other board using the device tree infrastructure, the foll...
有关idk-ps.dtso 文件的一些问题。 您能解释一下"lock_timer"计时器15的用途吗? 在"Mac"节点中、pps1_timer16_pwm 和 pps1_timer16_pwm2之间存在区别。 它们是否通过两个不同的引脚输出 PPS 信号? pps-ENABLE-GPIO 和 ref-ENABLE-GPIO 信号的特定用途是什么?
我们有自定义 tda4板、我们计划将来自 GPS 器件的 PPS 信号连接到 WKUP_GPIO0_12。 我们在内核中启用了 PPS 支持、并在 K3-j721e-common-proc-board.dts 文件中添加了以下更改: 我连接引脚 WKUP_GPIO0_12和 WKUP_GPIO0_13、并使用 ppstest 工具。日志如下: ...
Linux_for_Tegra/sources/hardware/nvidia/soc/t210/kernel-dts/tegra210-soc/tegra210-soc-base.dtsi pps { gpios = <&gpio TEGRA_GPIO(B, 7) 0>; compatible = "pps-gpio"; status = "okay"; }; I want to know is there any easier way to make it work?
硬件接口:3.3V、UART5(J58/H58, ttyTHS4)、PPS_GPIO(B58, GPIO_PA.00) BSP支持 1、添加PPS 支持 由于Xavier(NX/Nano/TX)不支持专用PPS硬件信号,通过软件将GPIO模拟接收PPS信号,修改如下: hardware\nvidia\platform\t19x\galen\kernel-dts\common\tegra194-p2888-0000-a00.dtsi ...
cp -r $kernel_out/arch/arm64/boot/dts/nvidia $JETPACK/kernel/dtb 编译前,需要修改三点: 1. kernel/kernel-5.10/arch/arm64/configs/tegra_defconfig CONFIG_PPS=y CONFIG_PPS_DEBUG=y CONFIG_PPS_CLIENT_KTIMER=y CONFIG_PPS_CLIENT_GPIO=y