PowerShell 複製 Set-NetFirewallRule -Name "WINRM-HTTP-In-TCP-PUBLIC" -RemoteAddress Any Cmdlet Set-NetFirewallRule 是由NetSecurity 模組導出。注意 不同版本的 Windows 防火牆規則名稱可能不同。 使用 Get-NetFirewallRule 查看規則清單。 啟用防火牆規則之前,請先檢視規則中的安全性設定,以確認設定適合您...
查看空闲内存 Get-WmiObject win32_OperatingSystem FreePhysicalMemory 查看磁盘总空间(单位MB) Get-WMIObject Win32_LogicalDisk |Where-Object{$_.Size}|Foreach-Object { 'Disk {0} has {1:0.0} MB totalspace' -f $_.Caption, ($_.Size / 1MB) } 查看防火墙状态 netsh advfirewall show currentprofile...
CommandType Name Version Source --- --- --- --- Function Get-NetFirewallServiceFilter 2.0.0.0 NetSecurity Function Set-NetFirewallServiceFilter 2.0.0.0 NetSecurity Cmdlet Get-Service 3.1.0.0 Microsof... Cmdlet New-Service 3.1.0.0 Microsof... Cmdlet New-WebServiceProxy 3.1.0.0 Microsof......
WinRM has been updated to receive requests. WinRM service type changed successfully. WinRM service started. WinRM has been updated for remote management. WinRM firewall exception enabled. 一對一遠端處理 如果您想要讓遠端會話成為互動式會話,則一對一遠端是您想要的。 此類型的遠端處理是透過Enter-PSS...
netsh advfirewall firewall show rule name="Remote Desktop - User Mode (TCP-In)" 停用Windows 防火牆 netsh advfirewall set allprofiles state off 進行疑難解答時,您可以使用此命令暫時排除 Windows 防火牆。 它會在下一次重新啟動時啟用,或使用下列命令加以啟用時。 請勿停止 Windows 防火牆服務 (MPSSVC...
我需要用PowerShell在Windows上打开一个端口,所以我就这样做了 netsh advfirewall firewall add rule name = "Open port 4443 test" dir=in action=allow protocol=TCP localport=4443 然后 Test-NetConnection -Port 4443 -ComputerName localhost 检查端口是否已打开但仍处于关闭状态。因此,我尝试使用另一个命令...
As you can see in the above screenshot, PowerShell is showing the status of Windows Firewall Public Profile as False which means that the Windows Firewall is disabled for that profile. You can also check the same in Windows Defender Firewall with Advanced Security UI. If you want to enabl...
0.0 0.0.0.0 # Create an address (type ipmask) Add-FGTFirewallAddress -Name 'My PowerFGT Network' -ip 192.0.2.1 -mask 255.255.255.0 q_origin_key : My PowerFGT Network name : My PowerFGT Network uuid : 9c65f75e-383e-51e9-a33a-caeffb7cfd33 subnet : 192.0.2.0 255.255.255.0 type :...
Ideally we'd like to use Powershell Get-NetFirewallRule, but we are not able to view the actual program path that was used when the rule was created. Here's the output of netsh.exe: netsh advfirewall firewall show rule name="Testing Notepad on port 5001" verbose ...
cd\ Clear-BCCache Clear-Disk Clear-DnsClientCache Clear-DnsServerCache Clear-DnsServerStatistics Clear-FileStorageTier Clear-Host Close-SmbOpenFile Close-SmbSession Configuration Connect-IscsiTarget Connect-VirtualDisk ConvertTo-DnsServerPrimaryZone ConvertTo-DnsServerSecondaryZone Copy-NetFirewallRule Copy...