WiSM Module, LAP,WLC,Port-channel, LAG 问题描述 在WiSM模块上的port channel状态和交换机侧的port channel 状态不一致导致不能访问WiSM模块,同时LAP不能注册到WLC。 WiSM 模块和6500/7600的接口配置 对于每个WiSM模块,和交换机背板的连接是交换机上虚拟的10个千兆接口,其中最后两个接口(interface 9 和interface ...
I am doing a redesign of my Freenas as I have now a Cisco Nexus 5596UP with lots of 10GB ports now. There has been a lot of threads about LACP and laggs to Enterprise switches with feedback and some saying "dont do it". Its kinda of hard to follow whats the best practice as ...
EtherChannel (also called port channel) can be used WITHOUT LACP, on Standard switches. LACP stands for Link Aggregation Control Protocol, and it is a protocol with an objective of ensuring that all uplinks in a LAG (Link Aggregation Group) are regularly checked to ensure that their link sta...
SW1 Lag: %LAG-5-MEMBER_REMOVED: Interface Ethernet7/4 has left Port-Channel10 due to:active interface speeds below minimum speed configuredSW1 Lag: %LAG-5-MEMBER_REMOVED: Interface Ethernet7/2 has left Port-Channel10 due to: active interface speeds below minimum speed configured SW1 Lag: ...
A - formed by Auto LAG Number of channel-groups in use: 1 Number of aggregators: 1 Group Port-channel Protocol Ports ---+---+---+--- 1 Po1(SU) LACP Gi1/0/47(s) Gi1/0/48(P) India-182-PoESW-1#sh int gi 1/0/47 GigabitEthernet1/0/47 is up, line protocol is down (su...
A - formed by Auto LAG Number of channel-groups in use: 13Number of aggregators: 13 Group Port-channel Protocol Ports---+---+---+---1 Po1(SU) LACP Te1/1/1(s) Te2/1/1(P)2 Po2(SU) LACP Te1/1/2(s) Te2/1/2(P) #sh interfaces te1/1/1 switchport Name: Te1/1/1...
The flow control settings are what caused the LAG/PortChannel on the Cisco side to dissolve the PortChannel Group. Virtual Connect by default is TX/RX Flow Control = OFF for Gigabit Ethernet uplink ports. Cisco typically by default is TX=Desired and RX=OFF for Gigabit Ethernet ports. [OFF...
(fxos)# show lacp interface ethernet 1/2 Interface Ethernet1/2 is up Channel group is 15 port channel is Po15 PDUs sent: 222828 PDUs rcvd: 207074 Markers sent: 0 Markers rcvd: 0 Marker response sent: 0 Marker response rcvd: 0 Unknown packets rcvd: 0 Illegal packets rcvd: 0 ...
SUB_INTF_ON_LAG_MEMBER_ERR="""\ Usage: add [OPTIONS] <subinterface_name> <vid> Try "add --help" for help. Error: Ethernet32 is configured as a member of portchannel. Cannot configure subinterface """ class TestSubinterface(object): @classmethod @@ -141,6 +147,21 @@ def test_inval...
port not aggregated due to minimum links not met u - unsuitable for bundling w - waiting to be aggregated d - default port A - formed by Auto LAG Number of channel-groups in use: 1 Number of aggregators: 1 Group Port-channel Protocol Ports ---+---+---+--- 1 Po1(SU) PAgP Fa...