+ "/n"; strShowAnwser += "The AddressFamily is: " + ipEP.AddressFamily + "...+= "The Min port number is: " + IPEndPoint.MinPort + "/n"; txtaShowAnswer.Value = strShowAnwser...is: 80 The AddressFamily is: InterNetwork The Max port number is: 65535 The Min port number is:...
<port_number>值表示要监视的端口。 对于TCP 端口,PortQry 报告以下状态之间的更改: CLOSE_WAIT 闭 既定 FIN_WAIT_1 LAST_ACK 听 SYN_RECEIVED SYN_SEND TIMED_WAIT 对于UDP 端口,PortQry 报告程序是否绑定到端口,但不报告 UDP 端口是否接收数据报。 若要停止监视,请按 Esc。 -wpid <pid> 监视进程 ID ...
set sp=<port_number>指定源端口 <port_number>值表示 PortQry 用于发送查询的端口。 PortQry 无法使用另一个进程已使用的端口。 如果指定端口号为零,则 PortQry 使用临时端口。 set protocol=<protocol> set p=<protocol>指定要使用的协议协议<>值表示要查询的端口类型(tcp或)。udpboth ...
-e [endpoint] port number and/or port ranges seperated by commas to query. For port range, the end port should be equal or greater than the start port. Valid port should be in range 1-65535. For example: 80,53,1024-1350. -r [end point range] range of ports to query (start:end)...
1.1.1 display interface display interface命令用来显示聚合接口的相关信息。 【命令】 display interface [ route-aggregation [ interface-number ] ] [ brief [ description | down ] ] 【视图】 任意视图 【缺省用户角色】 network-admin network-operator 【参数】 route-aggregation:显示三层聚合接口的相关信息。
待解决 悬赏分:1 - 离问题结束还有 portnumber should be between 1 and 65535问题补充:匿名 2013-05-23 12:21:38 端口号应介于1和65535 匿名 2013-05-23 12:23:18 端口号之间应1和65535 匿名 2013-05-23 12:24:58 portnumber应该在1和65535之间 匿名 2013-05-23 12:26:38 正在翻译,...
Channel 1 Slot 1 内存1通道插槽1(图中该插槽当前有内存) Size 显示内存总容量 Number of Ranks 内存颗粒数量 Manufacturer 内存制造商 3.3.2 Graphics Configuration界面 如图3-18所示,通过Graphics Configuration界面,可以查看显示配置,包括显示优先级顺序、动态共享内存大小设置。具体参数说明如表3-15所示。 图...
In addition to these physical ports, computers also have virtual ports, which are used to communicate with other devices or services over a network using specific protocols. These virtual ports are identified by a port number, which is a unique number assigned to each type of service or protoco...
Filter the output of the PORTList/-O report using the specified port number portnum or the keyword UNRSV. You can enter up to six filter values. The port number range is 1-65535. Restriction: For a UDP endpoint socket, the filter value only applies to the local or source port.Command...
port-number Specifies the port number that the Portal server uses to receive and encapsulate UDP packets from the device. The value is an integer that ranges from 1 to 65535. By default, the value is 50100. all Indicates that the device always uses the destination port number specified ...