1.1.5 display link-aggregation verbose display link-aggregation verbose命令用来显示已有聚合接口所对应聚合组的详细信息。 【命令】 display link-aggregation verbose [ route-aggregation [ interface-number ] ] [ all-configuration ] 【视图】 任意视图 【缺省用户角色】 network-admin network-operator 【参数】...
[sw1]interface Bridge-Aggregation 1 创建静态聚合组 [sw1-Bridge-Aggregation1]intg1/0/1 进入到接口 [sw1-GigabitEthernet1/0/1]portlink-aggregation group 1 将该接口加入聚合组中 [sw1-Bridge-Aggregation1]intg1/0/2 进入到接口 [sw1-GigabitEthernet1/0/2]portlink-aggregation group 1 将该接口加...
port trunk permit vlan 10,20,30 4. 链路聚合 4.1 创建链路聚合组:interface Bridge-Aggregation [组号] 例如:interface Bridge-Aggregation 1 4.2 将接口加入链路聚合组:interface [接口名] port link-aggregation group [组号] 例如:interface GigabitEthernet1/0/1 port link-aggregation group 1 5. 生成树协议...
group consensus. According to the different ways of convergence, the port convergence can be divided into three categories: manual gathering, static LACP aggregation, dynamic LACP aggregation. Experimental environment: two H3C E126A, ethernet1/0/24, ethernet1/0/23 converged into a link. Hand ...
5.将端口加入汇聚组 [SwitchA-GigabitEthernet1/0/1]port link-aggregation group 1 6.端口G1/0/2与端口G1/0/1的配置一致 7. 建立汇聚组2 [SwitchA]interface bridge-aggregation 2 8.进入端口G1/0/3 [SwitchA]interface gigabitethernet1/0/3 ...
gathering,staticLACPaggregation,dynamicLACPaggregation. Experimentalenvironment:twoH3CE126A,ethernet1/0/24, ethernet1/0/23convergedintoalink. Handpooling: Configurationofthefirstswitch: [H3CA]link-aggregationgroup10modemanual [H3CA]interfaceEthernet1/0/24 ...
问题描述: 想把端口g1/0/49设置成port linkaggregation group1,但是输完命令后提示:can't assgin the port to the aggregation group because its attribute configurations are different than the aggregate interface 组网及组网描述: 设备是接入层交换机 型号 s5130 2022-12-24提问 举报 (0) ...
因为后边不用加“1”，一个端口只能属于一个聚合组，所以删除的时候，敲到group就可以了，不用跟后边...
port link-aggregation group 1 在Kubernetes中实现端口链路汇聚(port link-aggregation)组1(group 1)是一个常见的操作,特别是在需要提高网络带宽和可靠性的场景下。在本文中,我将向你介绍如何通过Kubernetes实现这一操作,以及详细的步骤和代码示例。 ### 步骤概述...
5) 激活irf配置 [SW2] irf-port-configuration active 4.其他配置命令 4.1.端口捆绑配置命令 堆叠设备上配置捆绑 [SW1]int Bridge-Aggregation 2 [SW1]int ran ten 1/0/50 ten 2/0/51 [SW1-if-range]port link-aggregation group 2 [SW1]int Bridge-Aggregation 2 ...