端口隔离模式配置为二层隔离三层互通后,如需配置二层三层都隔离的模式,请执行命令port-isolate mode all。 端口隔离模式配置为二层三层都隔离后,如需配置二层隔离三层互通的模式,请执行命令port-isolate mode l2。 使用实例 # 配置端口隔离模式为二层隔离三层互通。 <HUAWEI>system-view[HUAWEI]port-isolate mode l...
port-isolate mode 12 interface gigabitethernet 1/0/1 port-isolate enable group 1 quit interface gigabitethernet 1/0/2 port-isolate enable group 1 quit 配置接口GE1/0/5至GE1/0/10的端口隔离功能,实现多个接口之间的二三层数据均隔离。 脚本: system-view port-isolate mode all port-group portgroup...
亲，你好，很高兴为您解答，答华为交换机端口隔离port-isolate mode默认为的是port-isolate mode all命令为启用所有端口隔离模式，但是不一定意味着所有端口都能够加入到隔离组里，加入到隔离组需要在接口下输入类似interface GigabitEthernet0/0/13port-isolate enable group 1 划入隔离组的命令，我感觉你再...
port-isolate mode Function The port-isolate mode command sets the port isolation mode. By default, ports are isolated at Layer 2 but can communicate at Layer 3. This function is supported only by the AirEngine 9700D-M and AirEngine 9700D-M1. Format port-isolate mode { l2 | all } Pa...
端口隔离port-isolate(二层隔离) port-isolate mode S2720-EI、S5720-LI、S5735-L、S5735S-L、S5735S-L-M、S5720S-LI、S6720-LI、S6720S-LI仅支持二层隔离三层互通,因此不支持此命令配置。 #HX interface GigabitEthernet1/0/1 eth-trunk 1 ...
Switch的端口隔离默认模式为二层隔离三层互通,隔离组默认为1。 port-isolate mode l2 port-isolate enable group 1 am isolate 配置当前端口与指定端口单向隔离。 clear configuration port- - isoelate 在全局模式下可以清除所有的端口隔离配置。
Switch的端口隔离默认模式为二层隔离三层互通,隔离组默认为1。 port-isolate mode l2 port-isolate enable group 1 am isolate 配置当前端口与指定端口单向隔离。 clear configuration port- - isoelate 在全局模式下可以清除所有的端口隔离配置。
[Huawei]port-isolate mode{l2|all} 缺省情况下,端口隔离模式为L2。 L2 端口隔离模式为二层隔离三层互通。 all 端口隔离模式为二层三层都隔离。 3.配置端口单向隔离 [Huawei-GigabitEthernet0/0/1]am isolate{interface-typeinterface-number}&<1-8>
The numbers given for multimode fiber-optic cable refer to the core diameter. For single-mode fiber-optic cable, 8.3 microns refers to the core diameter. The 9-micron and 10-micron values refer to the mode-field diameter (MFD), which is the diameter of the portion of the fiber that is...
Since then, we have been comparing the results ofbellhopcxx/bellhopcudato our modified Fortran version, not to the originalBELLHOP/BELLHOP3D. When we find a discrepancy, we find the failing ray, print out its state as it travels, find the step where it diverges, and isolate the part of...