PoE force power Status : Enabled 表1-2 display poe interface命令显示信息描述表 字段 描述 PoE Status PoE接口远程供电功能是否开启: · Enabled:开启 · Disabled:关闭 Power Priority PoE接口供电优先级: · Critical:最高 · High:高 · Low:低 Oper PoE接口工作状态: · Off:供电功能处于关闭状...
[HUAWEI-GigabitEthernet0/0/1] poe force-power Warning: Is there a valid PD connected to this interface? Yes or No?[Y/N]:y [HUAWEI-GigabitEthernet0/0/1] display this # interface GigabitEthernet0/0/1 port link-type access port default vlan 100 poe force-power poe legacy enable # 八、...
poe force-power enable 命令功能 poe force-power enable命令用来使能PoE强制供电功能。 undo poe force-power enable命令用来去使能PoE强制供电功能。 缺省情况下,未使能PoE强制供电功能。 命令格式 poe force-power enable undo poe force-power enable 参数说明 无 视图 Ethernet接口视图、GE接口视图 缺省级别 2:...
PoE force power Status : Disabled Table 2 Command output Field Description PoE Status PoE status: · Enabled. · Disabled. Power Priority Power supply priority: · Critical (highest). · High. · Low. Oper Operating status: · Off—PoE is disabled. · On—Power is being supplied to...
<Huawei> system-view [Huawei] clear poe interface Ethernet0/0/0 extern power over state The port Ethernet0/0/0 is abnormal state, force to clean abnormal state? [y/n]:y Info: Ethernet0/0/0 state is back to normal. 相关主题 display poe power-state display poe device 命令功能 displ...
H3C S5130S-28S-HP 本身就是poe交换机。所有端口供电默认就是开启的。
2、制供电set poe-port forcepower enable|disable7设置POE端口供电的优先级set poe-port priority 8设置POE设备的告警温度set poe temperature 9显示POE设备信息show poe10显示POE设备端口的信息show poe-port 11显示POE设备所有端口的优先级show poe-port priority12显示POE设备所有端口的供电级别show poe-port class...
set poe-port<portlist>powerlimit<value> 6.设置POE端口强制供电 set poe-port<portlist>forcepower[enable|disable] 7.设置POE端口供电的优先级 set poe-port<portlist>priority<1-3> 8.设置POE设备的告警温度 set poe temperature<value> 9.显示POE设备信息 show poe 10.显示POE设备端口的信息 show poe-po...
6、设置POE端口强制供电setpoe-port <portlist>forcepower[enable|disable] 7、设置POE端口供电的优先级setpoe-port <portlist>priority<1-3> 8、设置POE端口的告警温度setpoetemperature<value> 9、显示POE设备信息showpoe 10、显示POE设备端口的信息showpoe-port<portlist> 11、显示POE设备所有端口的优先级showpoe...
Power status: PoE/Medium Power (15.4 W) Please note that I'm using a PoE from Cisco (link below). https://www.amazon.com/Cisco-Business-Gigabit-Ethernet-Injector/dp/B00L0L0I9G Is there any CLI that force the AP to run at full power? thank you Cisco SB-PWR-I...