<probe>slaves= 2, slave_reg_ofs= 0x50, sliver_reg_ofs= 0x700, phy_id= 0:00, phy_if= 0x0 Detected MACID=5c:f8:21:42:1c:24 omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) <connect>PHY 0:00 not found <connect>PHY 0:01 not found IP...
{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */ {-1}, }; slaves的值为1,所以应该是只初始化了一路以太网,而且是eth0,我的板子只有一路接在rgmii2的网口。 在uboot里修改如下: 第一步,是...
PHY 0:00 not found net eth0: could not connect to phy 0:00 ADDRCONF(NETDEV_UP): eth0: link is not ready net eth0: DaVinci EMAC: ioctl not supported eth0 no wireless extensions. udhcpc (v1.13.2) started Sending discover...
[ 0.284669] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring e [ 0.284853] media: Linux media interface: v0.10 [ 0.284942] Linux video capture interface: v2.00 [ 0.285010] pps_core: ...
backup if you want. But I think using the official Armbian image so that the appropriate u-boot is used would be best. It's fine by me to wait for the newemmc. Also, when I said remote, I meant having you try out different images and sharing the logs, not remote access over ...
According to the datasheet, the PHY address is 0x1. When changed to this value the PHY id is correctly read. Before: [00:00:00.602,000] <err> phy_mii: No PHY found at address 0 After: [00:00:00.05...
12.2.0, GNU ld (GNU Binutils) 2.3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] MIPS: machine is Ubiquiti UniFi AP LR [ 0.000000] SoC: Atheros AR7241 rev 1 [ 0.000000] Initrd not found or empty - disabling initrd [...
[ 2.163733] pwm-backlight backlight-lvds: supply power not found, using dummy regulator[ 2.168545] mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed[ 2.172563] mxc_sdc_fb fb@0: registered mxc display driver ldb[ 2.203715] imx-ipuv3 2400000.ipu: IPU DMFC DP HIGH RESOLUTI...
While my later error message is "mdio:01 not found on slave 1". Instead of your "phy[2]" and "mdio:00, slave 0". This came up for me now because my Wi-Fi adapter just closed itself down for no obvious reason. I was handling the board, and might have interfered ...
• Any transmit/receive packet that is not completed when PE_RST_N goes to 0b is discarded. • Any in-band message that was sent over PCIe and was not acknowledged is re- transmitted over SMBus. 8 82577 GbE PHY—Interconnects 2.5 Figure 2. Intel® 5 Series Express Chipset/82577 ...