<probe>slaves= 2, slave_reg_ofs= 0x50, sliver_reg_ofs= 0x700, phy_id= 0:00, phy_if= 0x0 Detected MACID=5c:f8:21:42:1c:24 omap_rtc omap_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) <connect>PHY 0:00 not found <connect>PHY 0:01 not found IP...
{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */ {-1}, }; slaves的值为1,所以应该是只初始化了一路以太网,而且是eth0,我的板子只有一路接在rgmii2的网口。 在uboot里修改如下: 第一步,是...
PHY 0:00 not found net eth0: could not connect to phy 0:00 ADDRCONF(NETDEV_UP): eth0: link is not ready net eth0: DaVinci EMAC: ioctl not supported eth0 no wireless extensions. udhcpc (v1.13.2) started Sending discover...
[ 4.687042] CPSW phy found : id is : 0x221622 [ 4.693939] PHY 0:01 not found [ 4.699615] ADDRCONF(NETDEV_UP): eth0: link is not ready Starting Serial Getty on ttyO0... Started Serial Getty on ttyO0 [ OK ] .---O---. ...
According to the datasheet, the PHY address is 0x1. When changed to this value the PHY id is correctly read. Before: [00:00:00.602,000] <err> phy_mii: No PHY found at address 0 After: [00:00:00.05...
backup if you want. But I think using the official Armbian image so that the appropriate u-boot is used would be best. It's fine by me to wait for the newemmc. Also, when I said remote, I meant having you try out different images and sharing the logs, not remote access over ...
[ 0.068254] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator [ 0.068338] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator [ 0.068485] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy [ 0.071588] bam-dma-engine 704000.dma...
[ 2.163733] pwm-backlight backlight-lvds: supply power not found, using dummy regulator[ 2.168545] mxc_mipi_dsi 21e0000.mipi: i.MX MIPI DSI driver probed[ 2.172563] mxc_sdc_fb fb@0: registered mxc display driver ldb[ 2.203715] imx-ipuv3 2400000.ipu: IPU DMFC DP HIGH RESOLUT...
R-PHY#show core-files info -rw-r--r-- 1 root root 0 May 7 23:52 2.core.gz R-PHY#clear core-files Are you sure to clear all core files? [Confirm] Done. R-PHY#show core-files info No core files found. clear fault-management To clear an RPD event in the local queue or the...
• Any transmit/receive packet that is not completed when PE_RST_N goes to 0b is discarded. • Any in-band message that was sent over PCIe and was not acknowledged is re- transmitted over SMBus. 8 82577 GbE PHY—Interconnects 2.5 Figure 2. Intel® 5 Series Express Chipset/82577 ...