Zynq UltraScale+ MPSoC上电后,首先由BootROM对zynq设备进行初始启动,然后引导加载fsbl到OCM并启动fsbl;fsbl启动后加载PMU Firmware,然后加载ARM Trusted Firmware,配置DDR,最后将uboot加载到DDR并启动uboot;uboot启动后可选的加载hypervisor,并在hypervisor上运行linux系统,一般我们不使用hypervisor,而是直接使用uboot加载l...
回到主界面,“Firmware Version Configuration”可以用来修改定制的linux系统的主机名和产品名,默认与该Petalinux工程同名,如果需要可修改。“Yocto Settings”进行与Yocto相关的设置,这里就不做介绍了,一般保持默认即可。 按键盘上的右方向键(即右箭头),移动到底部的“Save”,按键盘上的“Enter”键,进入如下...
Image Packaging Configuration —>和镜像打包有关配置。Root filesystem type (INITRAMFS) —>:根文件系统设置。Copy final images to tftpboot,编译完petalinux工程之后自动将镜像文件拷贝到tftp服务器的目录,默认使能。同时可以设置tftpboot路径。Firmware Version Configuration —>配置固件版本名称,可任意设置。
回到主界面，“Firmware Version Configuration”可以用来修改定制的linux系统的主机名和产品名，默认与该...
Firmware Version Configuration ---> 在菜单中,移动光标到“Subsystem AUTO Hardware Settings - - ->”ENTER进入该菜单。将会出现类似以下菜单: --- Subsystem AUTO Hardware Settings System Processor(ps7 _ cortexa9 _ 0) ---> Memory Settings ---> ...
LinuxPetaLinux2016.4/2017.1 PetaLinux: Firmware Version Configuration not updated in the Linux image (Xilinx Answer 69122)2017.2 LinuxPetaLinux2017.1 PetaLinux: XSDK crashes when running petalinux-build (Xilinx Answer 69104)2017.2 LinuxPetaLinux2016.4 PetaLinux : Build (petalinux-build) failure when using ...
$ petalinux-config ---> Firmware Version Configuration ---> (2021.1.15) Firmware Version Target Logs: root@zynqmp-test:~# uname -a Linux zynqmp-test 5.10.0-xilinx-v2021.1 #1 SMP Fri Jun 4 15:57:16 UTC 2021 aarch64 GNU/Linux ...
ImportingHardwareConfiguration. StepsforFirmwareVersionConfiguration 1.ChangeintotherootdirectoryofyourPetaLinuxproject. $cdplnx-proj-root 2.Launchthetoplevelsystemconfigurationmenu. $petalinux-config 3.SelectFirmwareVersionConfiguration--. 4.SelectHostName,ProductName,FirmwareVersionaspertherequirementtoedit them. ...
Firmware Version Configuration 2.4 Change to boot from SD card Image Packaging Configuration Root filesystem type SD card 3. Create a new application/module petalinux-create-t apps-n$(app_name) petalinux-create-t modules-n$(module_name)
IMPORTANT! By default, besides the kernel, RootFS, and U-Boot, the PetaLinux project is configured to generate and build the other boot components for Zynq® FSBL, for Zynq UltraScale+ MPSoC FSBL and PMU firmware and for Versal PLM and PSM firmware . For more details on the auto ...