peer ebgp-max-hop命令用来配置允许BGP同非直连网络上的对等体建立EBGP连接,并同时可以指定允许的最大跳数。 undo peer ebgp-max-hop命令用来恢复缺省配置。 缺省情况下,只能在物理直连链路上建立EBGP连接。 命令格式 peer { group-name | ipv4-address | ipv6-address } ebgp-max-hop [ hop-count ] undo pe...
peer ebgp-max-hop命令用来配置允许BGP同非直连网络上的对等体建立EBGP连接,并同时可以指定允许的最大跳数。 undo peer ebgp-max-hop命令用来恢复缺省配置。 缺省情况下,只能在物理直连链路上建立EBGP连接。 命令格式 peer{group-name|ipv4-address|ipv6-address}ebgp-max-hop[hop-count] ...
51CTO博客已为您找到关于peer ebgp-max-hop的相关内容,包含IT学习相关文档代码介绍、相关教程视频课程,以及peer ebgp-max-hop问答内容。更多peer ebgp-max-hop相关解答可以来51CTO博客参与分享和学习,帮助广大IT技术人实现成长和进步。
Peer 2.2.2.2设备配置如下所示。as-number 300 Peer 1.1.1.1 ebgp-max-hop 2 Peer 1.1.1.1 connect-interface LoopBack0 peer 2.2.2.2 ebgp-max-hop 2 Peer 2.2.2.2 connect-interface LoopBack0 RTB: Bgp 200 Network 10.252.1.1 255.0 Undo snchronization ...
百度试题 结果1 题目要使非直连的EBGP邻居正常建立连接,必须包含如下哪个配置() A. peer connect- interface B. peer ebgp-max-hop C. peer ignore D. peer as-number 相关知识点: 试题来源: 解析 :B
在排除EBGP 邻居关系故障时,你发现两台直连设备使用Loopback 口建立连接,故执行display current-configuration configuration bgp 查看 peer ebgp-max-hop hop-count 的配置,下列哪项说法是正确的? A、 hop-count 必须大于 2 B、 hop-count 必须大于 15 ...
[HW-R6-bgp]peer 22.1.1.1 ebgp-max-hop 2 //手工修改跳数,否则BGP报文无法发送到对端,会处于IDLE状态 思科的实施: C-R6(config)#ip route 22.1.1.1 255.255.255.255 s1/0 C-R6(config)#do ping 22.1.1.1 sou lo0 C-R2(config)#ip route 66.1.1.1 255.255.255.255 s1/0 ...
The peer ebgp-max-hop command configures a BGP device to establish an EBGP peer relationship with a peer on an indirectly-connected network and set the maximum number of hops between the two devices. The undo peer ebgp-max-hop command restores the default setting. By default, an EBGP connect...
The peer ebgp-max-hop command configures a BGP device to establish an EBGP peer relationship with a peer on an indirectly-connected network and set the maximum number of hops between the two devices. The undo peer ebgp-max-hop command restores the default setting. By default, an EBGP connect...
The peer ebgp-max-hop command configures a BGP device to establish an EBGP peer relationship with a peer on an indirectly-connected network and set the maximum number of hops between the two devices. The undo peer ebgp-max-hop command restores the default setting. By default, an EBGP connect...