请在PE上进行如下配置。 操作步骤 执行命令system-view,进入系统视图。 执行命令bgp{as-number-plain|as-number-dot},进入BGP视图。 执行命令peeripv4-addressas-numberas-number,将对端PE配置为对等体。 执行命令peeripv4-addressconnect-interface loopbackinterface-number,指定BGP建立TCP(Transmission Control Protocol...
在BGP-VPN实例IPv6地址族视图下执行该命令后,PE把从本端CE学到的VPN路由引入BGP中,形成VPNv6路由发布给对端PE。 配置PE和CE间使用RIPng 在PE上进行如下配置。CE上配置普通RIPng协议,此处不再详述。有关RIPng的详细配置,请参见《S300, S500, S2700, S5700, S6700 V200R021C00, C01 配置指南-IP单播路由》...
The peer PE is configured as a BGP peer. Run peer ipv4-address connect-interface loopback interface-number An interface is used to set up a Transmission Control Protocol (TCP) connection with the BGP peer. A PE must use a loopback interface address...
PROBLEM TO BE SOLVED: To provide a protocol conversion device for allowing a master station to see a plurality of slave stations to be one slave station, so as to attain coexistence of an analog switchboard and a digital switchboard concerning a remote monitoring/control system in a distributing...
在BGP-VPN实例IPv6地址族视图下执行该命令后,PE把从本端CE学到的VPN路由引入BGP中,形成VPNv6路由发布给对端PE。 配置PE和CE间使用RIPng 在PE上进行如下配置。CE上配置普通RIPng协议,此处不再详述。有关RIPng的详细配置,请参见《S300, S500, S2700, S5700, S6700V200R024C00配置指南-IP单播路由》RIPng配置...
已经完成CE非对称接入PE的PW Redundancy功能的所有配置。 操作步骤 执行命令display mpls l2vc [ vc-id | interface interface-type interface-number | remote-info [ vc-id ] | state { down | up } ],查看L2VC的信息。 执行命令display mpls l2vc track admin-vc interface loopback interface-number [ ...
S300, S500, S2700, S5700, S6700 V200R023C10 配置指南-VPN 配置PE与PE间使用MP-IBGP 背景信息 请在PE上进行如下配置。 操作步骤 执行命令system-view,进入系统视图。 执行命令bgp{as-number-plain|as-number-dot},进入BGP视图。 执行命令peeripv4-addressas-numberas-number,将对端PE配置为对等体。
S300, S500, S2700, S5700, S6700 V200R023C10 配置指南-VPN 配置PE与PE间使用MP-IBGP 背景信息 在基本的BGP/MPLS IPv6 VPN组网中,PE之间需要通过MP-IBGP协议传递携带RD属性的VPNv6路由信息,实现VPN实例间的通信。由于所有的PE处于同一个AS,所以PE之间将建立MP-IBGP关系。在当前实现中,PE之间建立的是IPv4 ...
执行命令peer ipv4-address as-number as-number,将对端PE配置为对等体。 执行命令peer ipv4-address connect-interface loopback interface-number,指定BGP建立TCP(Transmission Control Protocol)连接的接口。 PE之间必须使用32位掩码的Loopback接口地址来建立MP-IBGP对等体关系,以便能够迭代到隧道。以Loopback接口地址为...
请在PE上进行如下配置。 操作步骤 执行命令system-view,进入系统视图。 执行命令bgp{as-number-plain|as-number-dot},进入BGP视图。 执行命令peeripv4-addressas-numberas-number,将对端PE配置为对等体。 执行命令peeripv4-addressconnect-interface loopbackinterface-number,指定BGP建立TCP连接的接口。