status = pci_msi_check_device(dev, 1, PCI_CAP_ID_MSI); if(status) returnstatus; WARN_ON(!!dev->msi_enabled); if(dev->msix_enabled) { dev_info(&dev->dev,"can't enable MSI " "(MSI-X already enabled)\n"); return-EINVAL; } status = msi_capability_init(dev);//此函数会配置...
status = pci_msi_check_device(dev, 1, PCI_CAP_ID_MSI); if(status) returnstatus; WARN_ON(!!dev->msi_enabled); if(dev->msix_enabled) { dev_info(&dev->dev,"can't enable MSI " "(MSI-X already enabled)\n"); return-EINVAL; } status = msi_capability_init(dev);//此函数会配置...
status=pci_msi_check_device(dev, nvec, PCI_CAP_ID_MSI); if(status) returnstatus; WARN_ON(!!dev->msi_enabled); /*Check whether driver already requested MSI-X irqs*/ if(dev->msix_enabled) { dev_info(&dev->dev,"can't enable MSI" "(MSI-X already enabled)\n"); return-EINVAL; }...
msix使用读写方式,msi使用pci操作寄存器方式。 都是获取message addr和message data __pci_write_msi_msg:if(entry->pci.msi_attrib.is_msix){void__iomem*base=pci_msix_desc_addr(entry);//目标msix entrywritel(msg->address_lo,base+PCI_MSIX_ENTRY_LOWER_ADDR);writel(msg->address_hi,base+PCI_MSIX...
pci_scan_single_device函数调用pci_scan_device扫描设备,扫描成功后把设备加入总线的设备链表。 最后的pci_scan_msi_device函数是检查设备的MSI能力,MSI和 设备的中断有关。 啊 8.2.5 扫描设备信息 扫描PCI设备通过读取PCI设备的配置空间完成,这部分原理在 第3章介绍过。扫描设备的代码pci_scan_device 函数: ...
MSI: 往预定义的内存地址写入预定义的消息来提出中断请求。 PCI设备->TLP消息-> Host Bridge -> CPU-> 内核->中断处理程序。 依赖于CONFIG_X86_LOCAL_APIC。 4. kconfig语法:Documentation/kbuild/kconfig-language.txt。 5. 源码: drivers/pci/Makefile; arch/x86/pci/Makefile。
and check your device entry. If it says Kernel driver in use: vfio-pci or thein useline is missing entirely, the device is ready to be used for passthrough. Mediated devices For mediated devices this line will differ as the device will be owned as the host driver directly, notvfio-pci....
一般情况下有是主板的驱动没有装完整.会显示pci device一般有网卡和声卡等PCI设备.如果你主板驱动装了,就看看网上邻居的属性里有没有本地连接,还有看看有没有声音图标.如果没有本地连接,那就是网卡,直接装网卡驱动.如果没有声音,就装声卡驱动.到...
(struct pci_dev*dev,conststruct pci_device_id*ent){int retval=0;//, intport, intmask;struct pcie_card*mypci;if(pci_enable_device(dev)){printk(KERN_ERR"IO Error.\n");return-EIO;}/*分配设备结构*/mypci=kmalloc(sizeof(struct pcie_card),GFP_KERNEL);if(!mypci){printk("In %s,...
其次,通过VFIO_DEVICE_GET_INFO命令获取vfio_device_info,包括设备bar region个数(最大6个bar)和中断个数。 再次,从PCI配置空间获取MSI-X BAR信息:bar index、bar的offset和size。检测MSI-X bar是否可映射,如果不可映射则返回失败。 最后,通过PCI配置空间读取每个bar地址域段信息,如下图所示,bar地址域段信息(32...