Result of the command: "packet-tracer input lan icmp 192.168.35.11 8 0 192.168.99.2" Phase: 1Type: ACCESS-LISTSubtype: Result: ALLOWConfig:Implicit RuleAdditional Information:MAC Access list Phase: 2Type: ROUTE-LOOKUPSubtype: inputResult: ALLOWConfig:Additional Information:in 192.168.99.0 255.255....
packet-tracer input [src_int] protocol src_addr src_port dest_addr dest_port [detailed] [xml] A few examples of truncated output show some of the most useful features. Not only does the tool show the result of an ACL evaluation, but also the specific ACE that either permits or denies ...
Result: input-interface: INSIDE input-status: up input-line-status: up output-interface: OUTSIDE output-status: up output-line-status: up Action: allow > Packet Tracer测试时的Snort级别捕获显示虚拟数据包: >capture-trafficPlease choose domain to capture traffic from: 0 - management0 1 - Router...
Here is the CLI syntax: packet-tracer input [src_int] protocol src_addr src_port dest_addr dest_port [detailed] [xml] A few examples of truncated output show some of the most useful features. Not only does the tool show the result of an ACL evaluation, but also the specific ACE that...
2、再输入configure t 进入全局配置模式，3、创建vlan 10命名为PC1，创建vlan 20名名为PC2，4、退出、通过wr保存如图：命令如下Switch>Switch>enSwitch#conSwitch#confSwitch#configure tEnter configuration commands, one per line. End with CNTL/Z.Switch(config)#vlan 10 name pc1^% Invalid input detected ...
Solved: Hello, I am trying to do a simple packet tracer on my ASA and this is what I am getting ASA# packet-tracer input DMZ tcp 10.250.0.5 2234 10.250.0.6 22 xml 1 ROUTE-LOOKUP input ALLOW in 10.250.0.4 255.255.255.252 DMZ 2 ACCESS-LIST DROP
12、 output rate 0 bits/secr 0 packets/sec 0 packete input, 00 no buf f erP.eceived 0 broadcastsr 0 rmits, 0 giaiits. 0 tlrottles 0 0 0 0 0 0 0input errors, 0 CD.C, 0 fraiiie, 0 ovemui, 0 iizniored, 0 atiort input packets with dribkile condition detects p ack et...
Router# configure terminal Router(config)# ip domain-name example.com Router(config)# crypto key generate rsa Router(config)# ip ssh time-out 60 Router(config)# ip ssh authentication-retries 2 Router(config)# line vty 0 4 Router(config-line)# transport input ssh Router(config-line)# exit...
Result: input-interface: inside input-status: up input-line-status: up output-interfce: outside output-status: up output-line-status: up Action: allow 次に、ユーザ CISCO\abc による内部ホスト 20.0.0.2 からのパケットをトレースし、トレース結果を XML 形式で表示する例を示します。...
1、在交换机上启动QOSSwitch(config)#mls qos //在交换机上启动QOS2、分别定义PC1(10.10.1.1)和PC2(10.10.2.1)访问控制列表Switch(config)#access-list 10 permit 10.10.1.0 0.0.0.255 //控制pc1上行流量Switch(config)#access-list 100 permit any 10.10.1.0 0.0.0.255 //控制...