i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set C 192.168.1.0/24 is directly connected, FastEthernet0/0 C 192.168.2...
该表格显示了运行RIP 协议的接口,以及可以接收和发送的RIP 路由更新的版本RIPv2 Automatic network summarization is in effect表示RIP 路由协议开启自动汇总功能 Maximum path: 4表示RIP 路由协议可以支持4 条等价路径,最大为6 条 注:可以通过下面的命令来修改RIP 路由协议支持等价路径的条数: R1(config-router)#max...
packet-tracer实验一、静态路由配置 网络拓扑结构如图所示: 地址表如下图所示: 1、首先,检查路由器接口 利用show ip route命令可显示路由表 show interfaces命令会显示接口状态,并给出路由器上所有接口的详细说明。如您所见,该命令的输出可能相当的长。如果要针对某一特定接口(例如FastEthernet 0/0)查看这些信息,请...
R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.2.2 //配置default route R1(config)#end R1# %SYS-5-CONFIG_I: Configured from console by console R1#show ip route //查看路由表 Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP ex...
Packet tracerEIGRP is an enhanced version of IGRP, and is a private routing protocol of Cisco Systems, Inc. We analyze the packet format of EIGRP and the advantages including PDM, RTP, DUAL, rapid convergence times, low usage of network resources, and route summarization. In Packet Tracer ...
ip route 0.0.0.0 0.0.0.0 192.168.2.2 ! ... ! line con 0 line vty 0 4 login ! ! ! end R1# R2: Router>en Router#conf t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R2 R2(config)#int fa0/0 R2(config-if)#ip add 192.168.2.2 255.255.25...
3.6.c Host route 3.6.d Floating static 3.7 Configure, verify, and troubleshoot RIPv2 for IPv4 (excluding authentication, filtering, manual summarization, redistribution) 4.1 Describe DNS lookup operation 4.2 Troubleshoot client connectivity issues involving DNS ...
EIGRP and OSPF are both partially supported in Cisco Packet Tracer 8.1.1 Router(config)#router eigrp 10 Router(config-router)#? auto-summary Enable automatic network number summarization distance Define an administrative distance eigrp EIGRP specific commands ...
versionnoservicetimestampslogdatetimenoservicetimestampsdebugdatetimemsecnoservicepassword-encryption!hostname!!ipaddressduplexautospeedauto!noipaddressduplexautospeedauto!ipaddress!interfaceSerial3/0noipaddress!noipaddress!noipaddress!ipiproute!!lineconlinevty04!!!PacketTracerPCCommandLine1.0IP :Subnet :...
使用Packet Tracer,正确配置网络参数,使用命令查看和分析RIP路由信息。 建立网络拓扑结构 配置参数 分析RIP路由信息 3. 实验报告 3.1 建立网络拓扑结构 网络拓扑图如下图所示: 3.2 配置参数 客户端的IP地址为192.168.1.14 路由配置: R1(config)#interface GigabitEthernet0/0 //进入R1路由器的G0/0端口配置ip ...