crypto Encryption module do To run exec commands in config mode enable Modify enable password parameters end Exit from configure mode exit Exit from configure mode hostname Set system's network name interface Select an interface to configure ip Global IP configuration subcommands line Configure a ter...
Enter configuration commands,one per line.EndwithCNTL/Z.Switch(config)# ps: configure terminal意为配置终端,单词较长,可采用以下解决办法: tab键自动补全 简写成conf t 4.全局配置模式 代码语言:javascript 复制 特权用户模式下的命令提示符:(configure)+#Switch(config)#?Configure commands:access-list Add a...
方法/步骤 1 【硬件连接】打开Packet Tracer工具，添加一台路由器，一台交换机和两台电脑，这些是我们实现单臂路由的硬件设备，如图所示。2 【硬件连接】通过直连线工具，将路由器的fa0/0连接交换机的fa0/1，将交换机的fa0/2连接PC1的fa0，将交换机的fa0/3连接PC2的fa0，如图所示。3 【IP设置】设置PC1的...
Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R1 R1(config)#int fa0/0 R1(config-if)#ip add 192.168.1.1 255.255.255.0 R1(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on ...
Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R1 R1(config)#int fa0/0 R1(config-if)#ip add 192.168.1.1 255.255.255.0 //配置端口IP地址 R1(config-if)#no shut %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up ...
24、utersnRoutericonf tEnter configuration commands/ one per line* End with CWTL/Router(config)tint f0/0Router tcoriig-if) -fip cdd 255.255.255. 0Router (conf ig-if) #no s扛Router(config-if)f%LTNK-5-CliANGED: Interface Fa s tE the me tO/ 0 changed state t思科设备配置有4种模式...
配置router0的f0/0端口ip Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z.Router(config)#interface f0/0 Router(config-if)#ip address 200.100.0.1 255.255.255.0 Router(config-if)#no shutdown LINK-5-CHANGED: Interface FastEthernet0/0, ...
2、按照提示符输入以下命令完成RA配置Router>enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname RARA(config)#interface Fa0/0RA(config-if)#ip address 192.168.1.1 255.255.255.0RA(config-if)#no shutdownRA(config-if)#exitRA(config...
Cisco Packet Tracer 方法/步骤 1 实验拓扑图：2 配置设备ip及网关路由器ip配置： Router>enableRouter#conf terEnter configuration commands, one per line. End with CNTL/Z.Router(config)#int f0/0Router(config-if)#ip add 192.168.1.1 255.255.255.0Router(config-if)#no shutRouter(config-if)#...
cisco-Packet-Tracer-使用教程手册.doc,cisco-Packet-Tracer-使用教程手册 PAGE69 / NUMPAGES116 Packet Tracer 5.0建构CCNA实验攻略(1)——配置Cisco交换机 Packet Tracer 5.0是一款非常不错的Cisco(思科)网络设备模拟器,对于想考思科初级认证(如CCNA)的朋友们来说,Pac