无线路由器通过DHCP获取IP。DHCP可以从服务器获取或者从路由器获取。所以,无线路由器无需设置default-gateway。这个是给二层交换机用得命令,目的是为了给配好虚拟地址得二层交换方便telnet管理。再说你想想,你得无线接入点是通过DHCP获取的IP地址,说明这是个三层设备,而default-gateway是给二层设备用的...
四、PC端登录测试 Packet Tracer PC Command Line 1.0 PC>ipconfig IP Address...: 192.168.1.2 Subnet Mask...: 255.255.255.0 Default Gateway...: 192.168.1.1 PC>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.2: bytes=32 time=12ms TTL=128 Reply from 192.168...
Gateway of last resort is not set S 192.168.1.0/24 [1/0] via 192.168.5.2 C 192.168.2.0/24 is directly connected, FastEthernet1/0 C 192.168.5.0/24 is directly connected, Serial2/0 R2# 五、测试 Packet Tracer PC Command Line 1.0 PC>ipconfig IP Address...: 192.168.1.2 Subnet Mask......
6.4.3.4 Packet Tracer - Troubleshooting Default Gateway Issues 对默认网关问题进行故障排除Packet Tracer -对默认网关问题进行故障排除 地址分配表 设备 接口 IP地址 子网掩码 默认网关 R1 G0/0 192.168.10.1 255.255.255.0 未提供 G0/1 192.168.11.1 255.255.255.0 未提供 S1 VLAN 1 192.168.10.2 255.255.255.0...
Packet Tracer PC Command Line 1.0 PC>ipconfig IP Address...: 192.168.1.2 Subnet Mask...: 255.255.255.0 Default Gateway...: 192.168.1.1 PC>ping 192.168.4.2 Pinging 192.168.4.2 with 32 bytes of data: Request timed out. Request timed
Packet Tracer PC Command Line 1.0 PC>ipconfig IP Address...: 192.168.1.2 Subnet Mask...: 255.255.255.0 Default Gateway...: 192.168.1.1 PC>ping 192.168.2.2 Pinging 192.168.2.2 with 32 bytes of data: Reply from 192.168.2.2: bytes=32...
只要你的路由器没有配置缺省路由,即默认路由,show ip route 的结果,最上方就会出现Gateway of last resort is not set。你可以配置一条缺省路由 ip route 0.0.0.0 0.0.0.0 ip-addr之后,再show ip route,可以看到这名话变成你的默认路由。
-配置默认网关,同时设定DNS服务器地址,输入命令“default-router GATEWAY”; -“GATEWAY”是指默认网关地址; -确认DHCP配置,输入命令“show dhcp pool POOL NAME”。 12. [如何进行Ping测试] 在Packet Tracer中进行Ping测试的方式可以参考以下步骤: -在一个命令窗口中输入Ping命令“ping IP地址”(如ping 192.168.1....
2) traceroute command And see where it is timing out. 3) Use the debug ip packet command: Not sure if it works in packet tracer you can debug the actual access-list: debug ip packet CiscoRtr# debug ip packet BRANCH_OFFICE_LAN_To_INTERNETA detail # undebug all (to stop it) Expand...
2) traceroute command And see where it is timing out. 3) Use the debug ip packet command: Not sure if it works in packet tracer you can debug the actual access-list: debug ip packet CiscoRtr# debug ip packet BRANCH_OFFICE_LAN_To_INTERNETA detail # undebug all (to stop it) Expand...