ovs-vsctldel-fail-mode ovs-br 设置fail-mode ovs-vsctlset-fail-mode br-ex secure 设置tag ovs-vsctlsetport eth0-stor tag=102 清除tag ovs-vsctl clear port br-eth1--br-mgmt tag ovs设置网桥MAC ovs-vsctlsetbridge br-storage other-config:hwaddr=fa:16:3e:fe:8f:79...
ovs-vsctl [--may-exist] add-br br0 删除bridge删除bridge br0使用选项--if-exists后,若欲删除的bridge不存在,该命令什么也不做,也不报错。ovs-vsctl [--if-exists] del-br br0 查询已有的 bridgeovs-vsctl list-br 端口相关命令添加端口添加端口(物理端口或vNIC)eth1到bridge eth1中...
ovs-vsctl [--may-exist] add-port br0 eth1 创建bond 在br0上创建一个bond了eth0,eth1和eth2的bond端口bond0 # ovs-vsctl add-bond <bridge> <port> <iface...> ovs-vsctl add-bond br0 bond0 eth0 eth1 eth2 移除端口 从br0上移除端口eth1 ovs-vsctl [--if-exists] del-port br0 eth1 ...
ovs-vsctl set-controller br0 tcp:1.2.3.4:6633 tcp:4.3.2.1:6633 ovs-vsctl del-controller br0 ovs-vsctl get-controller br0 ovs-vsctl set port eth0 tag=10 添加eth1到指定bridge br0中，同时将其配置成指定VLAN 10的access端口 ovs-svctl add-port br0 eth1 tag=10 在br0上...
ovs-svctl add-port br0 eth1 tag=10 配置端口为Trunk口 在br0上添加port eth1为VLAN 10,11的trunk ovs-vsctl add-port br0 eth1 trunk=10,11 在bridge ovs0中添加远端IP为10.10.10.1的VXLAN endpoint端口vxlan0 # key=100表示设置vni为100,不设置默认为0ovs-vsctladd-port ovs0 vxlan0--setinterface...
2.删除名为br0的网桥 ovs-vsctl del-br br0 3.列出所有网桥 ovs-vsctl list-br 4.判断网桥br0是否存在 ovs-vsctl br-exists br0 5.列出挂接到网桥br0上的所有网络接口 ovs-vsctl list-ports br0 6.将网络接口eth0挂接到网桥br0上 ovs-vsctl add-port br0 eth0 ...
ovs-vsctl add-br br0 ovs-vsctl add-port br0 eth0 Alternatively, perform both operations in a single atomic transaction: ovs-vsctl add-br br0 -- add-port br0 eth0 Delete bridge br0, reporting an error if it does not exist: ovs-vsctl del-br br0 Delete bridge br0 if it exists...
#ovs-vsctl del-port BR IF-NAME 4 查看mac ovs-appctl fdb/show s1 5 查看网桥配置 ovs-vsctl list bridge s1 6 查看端口配置 ovs-vsctl list port s1 s1-eth1 --- 一 基础测试: # nmcli device DEVICE TYPE STATE CONNECTION team0 team connected team...
[root@vrouter1 ~]# dpdk-devbind -b vfio-pci eth0 [root@vrouter1~]# ovs-vsctl add-port ovs-br0 pci_port1 --setInterface pci_port1 type=dpdk options:dpdk-devargs=0000:03:00.1 root@vrouter1 ~# ovs-vsctl add-br ovs-phy --setbridge ovs-phy datapath_type=netdev ...