ospf timer hello命令用来设置接口发送Hello报文的时间间隔。 undo ospf timer hello命令用来恢复该时间间隔的缺省值。 缺省情况下,P2P、Broadcast类型接口发送Hello报文的时间间隔的值为10秒;P2MP、NBMA类型接口发送Hello报文的时间间隔的值为30秒。 命令格式 ...
T1模式:1.544 Poll(单位—秒):路由器发送轮询报文的时间间隔——不是固定的值—hello时间的四倍—时间可更改(是hello时间四倍的倍数) 轮询ping测:ping 备份路由器的IP地址(每一个路由器轮回ping测)、 Retransmit ——邻接路由器重传LSA的时间间隔——时间可更改 Transmit Delay ——接口在传送LSA的延迟时间 组播...
ospfv3 timer hello命令用来设置接口实例上发送Hello报文的时间间隔。 undo ospfv3 timer hello命令用来恢复接口实例上该时间间隔的缺省值。 缺省情况下,P2P、Broadcast类型接口发送Hello报文的时间间隔的值为10秒,P2MP、NBMA类型接口发送Hello报文的时间间隔的值为30秒。 命令格式 ospfv3 timer hello interval [ conserv...
6.Hello间隔与Dead时间一致 修改Hello时间,Dead会自动变为Hello的4倍 配置: [R1]in g0/0/1 [R1-GigabitEthernet0/0/1]ospf timer hello 20 报错提示:Hello timer mismatch 7.末节区域标识一致: Extern option mismatch 报错提示
[Sysname-Vlan-interface10] ospf timer hello 201.1.59 ospf timer poll【命令】ospf timer poll secondsundo ospf timer poll【视图】接口视图【缺省级别】2:系统级【参数】seconds:向状态为down的邻居路由器发送轮询Hello报文的时间间隔,取值范围为1～2147483647,单位为秒。
I change R2's hello interval to 5 second. Its dead timer becomes 20 seconds. R3's dead timer would still be 40 seconds. And it sends hello every 10 seconds. Now when R2's dead timer reaches 10 (10 seconds passed), it would get a hello packet from R3. R2 would restart counting ...
I change R2's hello interval to 5 second. Its dead timer becomes 20 seconds. R3's dead timer would still be 40 seconds. And it sends hello every 10 seconds. Now when R2's dead timer reaches 10 (10 seconds passed), it would get a hello packet from R3. R2 would restart counting ...
请确保邻居路由器两端的Hello定时器和邻居失效时间的值保持一致,否则将影响OSPF邻居关系的建立。 3. 配置步骤 (1) 进入系统视图。 system-view (2) 进入接口视图。 interface interface-type interface-number (3) 配置Hello定时器。 ospf timer hello seconds 缺省情况下,P2P、Broadcast类型接口发送Hello报文的时间...
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 oob-resync timeout 40 Hello due in 0:00:03 Supports Link-local Signaling (LLS) Cisco NSF helper support enabled IETF NSF helper support enabled Index 1/2, flood queue length 0 ...
router mode commands/options: lsa OSPF LSA timers nsf OSPF NSF timer pacing OSPF pacing timers throttle OSPF throttle timers ciscoasa(config-router)# timers nsf ? 步骤3 输入平稳重启等待间隔。此值的范围为 1 到 65535。 示例: ciscoasa(config-router)# timers nsf wait 200 通过...