[r1-GigabitEthernetoro/0]ospf timer hello 20 Dead时间 [r1-GigabitEtherneto/0/0]ospf timer dead 120 注意:修改hello时间,则死亡时间随之改变,而仅修改死亡时间,hello间隔时间不变。 OSPF特殊区域标记 跟修改掩码效果相同。 认证字段 两者均需要等待死亡时间超时,才会从full状态切换到down状态。 DBD包 使用未携...
客户网络反馈NetEngine 8000 修改ospf timer hello 1 时间不生效 处理过程 核实如下:在配置Hello报文发送时间间隔并且不配置ospf timer dead的情况下,OSPF邻居失效时间为Hello报文发送时间间隔的4倍。因此,当Hello报文发送时间间隔的取值小于或等于2时,OSPF邻居失效时间会小于10秒,但是如果OSPF邻居失效时间小于10秒,且在...
ospf timer hello命令用来设置接口发送Hello报文的时间间隔。 undo ospf timer hello命令用来恢复该时间间隔的缺省值。 缺省情况下,P2P、Broadcast类型接口发送Hello报文的时间间隔的值为10秒;P2MP、NBMA类型接口发送Hello报文的时间间隔的值为30秒。 命令格式 ...
OSPF是一种重要的内部网关路由协议,通过交换Hello消息进行邻居发现和维护,以及通过Dead间隔检测邻居失效。Hello间隔用于周期性交换Hello消息,建立邻居关系,而Dead间隔则用于判断邻居路由器是否失效。网络管理员可以根据网络的特点和需求,适当调整Hello和Dead间隔,以优化网络的性能和稳定性。 然而,调整Hello和Dead间隔时需要谨...
默认情况下,ospf的接口下hello的死亡时间为hello时间的4倍。默认的hello的时间为10秒钟,Dead Intervel 为40秒。 修改hello的时间值。进入到接口模式下 int g0/0/0 ospf timer hell 3 修改前:如下图 修改之后:如下图--- 修改之后,由于两边的Hello时间不一致了,邻居就会down掉的哦。
Transmit Delay is 1 sec, State BDR, Priority 1 Designated Router (ID) 10.3.11.1, Interface address 10.3.11.1 Backup Designated router (ID) 10.6.11.1, Interface address 10.3.11.2 Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5 ...
An interface's hello timer can be adjusted: Router(config-if)# ip ospf hello-interval If we set Router1 to use a hello timer of 15 seconds and leave Router2 at its default setting of 10 seconds, they will not form an adjacency. Note that this behavior is different from EIGRP. If ...
在WaitingTimer触发前,发送的Hello报文是没有DR和BDR字段的。在Waiting阶段,如果收到Hello报文中有DR和BDR,那么直接承认网络中的DR和BDR,而不会触发选举。直接离开Waiting状态,开始邻居同步。 假设网络中已经存在一个DR和一个BDR,这时新加入网络中的路由器,不论它的Router ID或者DR优先级有多大,都会承认现网中已有...
State: Full Mode:Nbr is Master Priority: 1 DR: 10.1.1.2 BDR: None MTU: 0 Dead timer due in 34 sec Retrans timer interval: 5 Neighbor is up for 00:00:03 Authentication Sequence: [ 0 ] 如果没有任何OSPF邻居信息显示,检查邻居两端的接口物理状态和协议状态是否UP,状态是否稳定,接口是否有...
An interface's hello timer can be adjusted: Router(config-if)# ip ospf hello-interval If we set Router1 to use a hello timer of 15 seconds and leave Router2 at its default setting of 10 seconds, they will not form an adjacency. Note that this behavior is different from EIGRP. If ...