(your statement above assumes that the area is already configured a stub from your previous stub area configuration) that's why you just add they last command #area x stub no-summery. If the area you want to make totally stubby was not already a stub area then you have to add the comm...
4)在area 2 配置Stub区域 4、配置过程: 步骤一:修改网络设备默认名称、配置好IP地址 路由器R1做基础接口配置,并修改设备名称 Router>en //进入特权模式 Router#conf t //进入全局配置模式 Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname R1 //给设备改名称 R1(confi...
Cisco Learning Network Podcast
4)在area 2 配置Stub区域 4、配置过程: 步骤一:修改网络设备默认名称、配置好IP地址 [if !supportLists]1) [endif]路由器R1做基础接口配置,并修改设备名称 Router>en //进入特权模式 Router#conf t //进入全局配置模式 Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname...
An ASBR cannot exist in a stub area to import AS external routes. Virtual links cannot exist in stub areas. Pre-configuration Tasks Before configuring OSPF stub areas, complete the following tasks: Configure IP addresses for interfaces to ensure that neighboring nodes are reachable at the network...
NSSA Area Configure Change:NSSA区域配置发生变化 Stub Area Configure Change:Stub区域配置发生变化 Received Invalid DD Packet:收到无效的DD报文 Not Received DD during RouterDeadInterval:在Dead定时器启动期间,没有收到DD报文 M,I,MS bit or SequenceNum Incorrect:收到的DD报文中M、I、MS比特位与协议规定不...
ospf process-id area area-id [ exclude-subip ] 缺省情况下,未配置接口使能OSPF。 1.5 配置OSPF特殊区域 1.5.1 功能简介 网络管理员对整个网络划分区域完毕后,可以根据组网需要进一步将区域配置成Stub区域或NSSA区域。 当非骨干区域不能与骨干区域保持连通,或者骨干区域因为各方面条件的限制无法保持连通时,可以通过...
二、STUB配置 1、OSPF关键配置 1)、R1 OSPF关键配置 [R1]display current-configuration configuration ospf ospf 1 router-id 1.1.1.1 area 0.0.0.0 network 10.1.12.1 0.0.0.0 network 10.1.13.1 0.0.0.0 network 1.1.1.1 0.0.0.0 2)、R2 OSPF关键配置 ...
[Sysname-ospf-100-area-0.0.0.1] default-cost 20【相关命令】· nssa· stub1.1.10 default-route-advertisedefault-route-advertise命令用来将缺省路由引入到OSPF路由区域。undo default-route-advertise命令用来恢复缺省情况。【命令】default-route-advertise [ [ always | permit-calculate-other ] | cost cost-...
2:配置单区域(area0 )的 OSPF [R1]ospf 1 router-id 11.1.1.1 //配置 OSPF 的进程号以及 route-ID [R1-ospf-1]area 0 //进入到区域 0 里面。 [R1-ospf-1-area-0.0.0.0]network 12.1.1.1 0.0.0.0 //精确宣告一个 IP 地址。 [R1-ospf-1-area-0.0.0.0]network 11.1.1.1 0.0.0.0 ...