针对你提出的问题“ospf process 1 cannot start. there must be at least one 'up' ip interface”,这里有一些详细的步骤和解释来帮助你解决问题: 1. 确认OSPF进程配置正确 首先,你需要确认OSPF进程的配置是正确的。在思科路由器上,配置OSPF的基本命令如下: plaintext router ospf 1 network 192.168.1.0 0.0....
小弟我用的是“工大瑞普虚拟思科实验室 full2(u7.2)”版的模拟器当我输入:R3(config)#router ospf 1 vrf AS时,会出现:OSPF process 1 cannot start.There must be at least one "up" IP interface,for OSPF to use as router ID(ospf 1的进程无法启动,原因:至少需要一个"up"的接口为ospf提供id)....
[process-id] OSPF进程。 RouterId 交换机标识。 TransitAreaId 传输区域标识。 HelperVirtNbrCount Helper的虚连接邻居数。 HelperShamLinkNbrCount Helper伪连接邻居数。 HelperNormalNbrCount Helper正常连接邻居数。 可能原因 OSPF通过虚连接发现预重启邻居。 处理步骤 正常运行信息,无需处理。OSPF...
OSPF/6/BACKUP_LENGTH_ERR:The data length was unidentifiable in the restoration process. (Type=[STRING], Length=[USHORT]) 日志含义 SMB在数据恢复过程中,TLV数据的长度不可识别。 日志参数 可能原因 TLV的数据长度不一致。 处理步骤 执行display current-configuration ospf命令检查主备板配置是否一致。 1)Y=...
router ospf 1什么意思 ospf process 1 with router id 需求: 1)按拓扑中区域Area要求,在每台路由器启用OSPF,使得整个网络可以互连互通。 n进程号Process ID配置为每台设备的主机编号,如R1配置为router ospf 1. n路由器ID请使用router-id手工指定,如R1为router-id 1.1.1.1....
OSPF下命令的语法: timers throttle spf[spf-start] [spf-hold] [spf-max-wait] 其中: • spf-start — 在更改后安排SPF计算的初始延迟(以毫秒为单位).范围为1至600000. • spf-hold — 两次连续SPF计算之间的最短保持时间(以毫秒为单位).范围为1至600000. • spf-max-wait — 两次连续SPF计算之间...
If a router must use a route to advertise LSAs carrying an external default route, the route cannot be a route in the local OSPF AS. This means that the route cannot be a route learned by the local OSPF process. This is because default external routes are used to guide packet forwarding...
cumulus@switch:~$ sudo systemctl start frr.service Configure OSPF Before you configure OSPF, you need to identify: Which router has the router ID With which device the router communicates What information to advertise (the prefix reachability) ...
timers throttle spf[spf-start] [spf-hold] [spf-max-wait] 其中: spf-start— 在更改后安排SPF计算的初始延迟(以毫秒为单位)。范围为1至600000。 spf-hold— 两次连续SPF计算之间的最短保持时间(以毫秒为单位)。范围为1至600000。 spf-max-wait— 两次连续SPF计算之间的最大等待时间(以毫秒为单位)。范围...
However, you cannot use both configuration methods at the same time. Here is an example of configuring OSPF per interface: cumulus@switch:~$ net add interface swp1 ospf area 0.0.0.0 You can use the net add ospf passive-interface default command to set all interfaces as passive and the ...