执行命令lsa-arrival-interval{interval|intelligent-timermax-intervalstart-intervalhold-interval},配置LSA接收的时间间隔。 interval为LSA被接收的时间间隔,单位是毫秒。 intelligent-timer表示通过智能定时器设置OSPF Router LSA和Network LSA的更新间隔时间。
undo ospfv3 peer hold-max-cost timer [ hold-max-cost-value ] [ instance instance-id ] Parameters ParameterDescriptionValue instance instance-id Specifies the ID of the instance to which an interface belongs. The value is an integer ranging from 0 to 255. timer hold-max-cost-value Speci...
1.1.60 ospfv3 peer 1.1.61 ospfv3 peer hold-max-cost duration 1.1.62 ospfv3 prefix-suppression 1.1.63 ospfv3 primary-path-detect bfd 1.1.64 ospfv3 timer dead 1.1.65 ospfv3 timer hello 1.1.66 ospfv3 timer poll 1.1.67 ospfv3 timer retransmit 1.1.68 ospfv3 trans-delay 1.1.69 pic 1.1...
ospfv3 peer hold-max-cost duration timer [ instance instance-id ] 缺省情况下,未配置OSPFv3邻居保持最大开销值的时间。 1.6.8 配置OSPFv3最大等价路由条数 1. 功能简介 如果到一个目的地有几条开销相同的路径,可以通过等价路由负载分担来提高链路利用率。 2. 配置步骤 (1) 进入系统视图。 system-view (...
Ospf timer pool time 1---3600S 默认120S 接口下 至少为hello报文发送时间的4倍 3.5.4 OSPF网络属性管理 Display ospf 100 lsdb *** 查看数据库信息 Display ospf 100 peer *** 查看(指定)邻居信息 Display ospf 100 routing router-id 3.5.5 OSPF的DR选举配置示例 广播网络...
timer-interval transmit-interval:可多选参数,设置每次泛洪更新LSA的时间间隔,取值范围为30~100000ms,缺省值是30。如果发现频繁有邻居路由器断开的日志提示时,可适当加大本参数值。 3.4.6 OSPF基本功能管理 display ospf 100 peer display ospf 100 interface ...
<SwitchA>display ospf peerOSPFProcess1withRouterID10.1.1.1Neighbors Area0.0.0.0interface192.168.0.1(Vlanif10)'s neighbors RouterID:10.2.2.2Address:192.168.0.2State:Full Mode:Nbr is Master Priority:1DR:192.168.0.2BDR:192.168.0.1MTU:0Dead timer duein36sec ...
Cost: 1 Transmit Delay is 1 sec, State DR, Priority 1, MTU 1500, MaxPktSz 1500 BFD enabled, BFD interval 150 msec, BFD multiplier 3, Mode: Strict Designated Router (ID) 2.2.2.2, Interface address 10.1.1.2 No backup designated router on this network ...
ospf suppress-flapping peer hold-max-cost disable //用来取消Hold-max-cost邻居震荡抑制模式。 ospf timer dead //用来设置OSPF的邻居失效时间。 ospf timer hello //用来设置接口发送Hello报文的时间间隔。 ospf timer poll //用来配置NBMA网络上发送轮询Hello报文的时间间隔。
执行命令ospfv3 suppress-flapping peer hold-downinterval[instanceinstance-id],配置震荡抑制模式为Hold-down模式,并设置抑制持续时间。 OSPFv3邻居震荡抑制分为Hold-down和Hold-max-cost两种模式: Hold-down模式:针对邻居建立过程中的频繁泛洪和拓扑变化的问题,在一段时间内禁止该邻居重新建立,避免频繁的数据库同步和...