ospf ldp-sync命令用来使能接口的LDP和OSPF联动功能。 undo ospf ldp-sync命令用来去使能接口的LDP和OSPF联动功能。 缺省情况下,接口上未使能LDP和OSPF联动功能。 命令格式 ospf ldp-sync undo ospf ldp-sync 参数说明 无 视图 GE接口视图、10GE接口视图、40GE接口视图、Eth-Trunk
OSPF/6/LDP_SYNC_EVENT: Interface [IfName] received LDP event [LdpEvent], LDP synchronization state [PrevState] change to [CurrentState]. (AreaId=[AreaId], SuppressCount=[SuppressCount]) 日志含义 LDP联动状态发生迁移。 日志参数 参数名称参数含义 ...
ospf timer ldp-sync hold-down命令用来设置接口不建立OSPF邻居而等待LDP会话建立的时间间隔。 undo ospf timer ldp-sync hold-down命令用来恢复缺省配置。 缺省情况下,不建立OSPF邻居而等待LDP会话建立的时间间隔是10秒。 命令格式 ospf timer ldp-sync hold-downvalue ...
作用:ospf ldp-sync命令是用来使能接口的LDP和OSPF联动功能。 应用场景: (1)在存在主备链路的网络中,当主链路故障恢复后,流量会从备份链路切换到主链路。由于OSPF的收敛在LDP会话建立之前完成,导致旧的LSP已经删除,新的LSP还没有建立,因此LSP流量中断。LDP和IGP同步通过抑制IGP建立邻居关系来推迟路由的回切,直至LDP...
LDP-sync enabled, Hold Down: 10, Max Cost: Infinite, LDP-sync State: Init 表1-6 display ospf interface命令显示信息描述表 字段 描述 Area 接口所属的区域ID IP address 接口IP地址(不管是否使能了流量工程) Type 接口的网络类型,取值为: · PTP表示网络类型为点对点 · PTMP表示网络类型为点对多...
LDP sync state: AchievedPrefix-SID type: IndexValue: 876, Explicit-null, N-flag-clearProcess ID: ospf 1Prefix-SID validity: Invalid表1-19 display ospf interface verbose命令显示信息描述表字段 描述 Interface 接口IP地址等信息 MTU 最大传输单元 Timers OSPF定时器的值,其中: · Hello:表示接口...
日志信息 OSPF/6/LDP_SYNC_FIRE: Interface [IfName] LDP synchronization hold maximum cost timer expired. (AreaId=[AreaId]) 日志含义 LDP联动Hold max cost定时器超时。 日志参数 参数名称参数含义 IfName 接口名称。 AreaId OSPF的区域标识。 可能原因 定时器超时。 处理步骤 正常运行信息,无需处理。翻...
To disable LDP-IGP synchronization, use the no form of this command. mpls ldp sync [disable] no mpls ldp sync Syntax Description disable (Optional) Disables MPLS LDP synchronization from within the OSPF interface and area configuration submodes only. For the ...
RP/0/RP0/CPU0:router(config-ospf-vrf)# area 1 mpls ldp sync Enables LDP IGP synchronization on an interface for the specified VRF. Step 6 Use the commit or end command. commit —Saves the configuration changes and remains within the configuration session. end —Prompts user ...
Run the ospf ldp-sync command to enable synchronization between LDP and OSPF to prevent traffic loss in the preceding problems. Run this command on the interfaces on both ends of the link between the node where the primary LSP and the backup LSP diverge from each other and its LDP peer...