$ chmod +x /etc/init.d/mac-change.sh $ /etc/init.d/mac-change.sh enable 测试是否生效 $ /etc/init.d/mac-change.sh enabled && echo on $ /etc/init.d/mac-change.sh start 更改无线MAC端口地址--尚未实现自启动 在openwrt里面一般把整个flash分为几个分区,uboot、kernel、rootfs、rootfs_da...
Yes, mac-address and local-mac-address can be set by u-boot (see fdt_fixup_ethernet), and they take priority: https://elixir.bootlin.com/linux/v6.6.30/source/net/core/of_net.c#L126 OpenWrt via netifd will also change device MAC address if asked to, so make sure there are no mac...
基于Openwrt虚拟路由MAC地址 基于Openwrt虚拟路由MAC地址上传开发板执⾏程序 scp传输⽂件 将⽣成好的可执⾏⽂件放到开发板上，⽂件传输⽅式 SCP。scp 是 secure copy 的缩写, scp 是 linux 系统下基于 ssh 登陆进⾏安全的远程⽂件拷贝命令。基本⽤法为 scp 本地⽂件⽬标系统同户名@⽬...
# Change this to your host's public address - WG_HOST=raspberrypi.local # Optional: # - PASSWORD_HASH=$$2y$$10$$hBCoykrB95WSzuV4fafBzOHWKu9sbyVa34GJr8VV5R/pIelfEMYyG (needs double $$, hash of 'foobar123'; see "How_to_generate_an_bcrypt_hash.md" for generate the hash) # -...
1、system_init中调用create_event_socket创建监听netlink的socket 2、当接口link up或者link down时,在内核中调用netif_carrier_on,最终会走到netdev_state_change, 再通过rtmsg_ifinfo发出netlink消息。 3、在system_init中注册的cb_rtnl_event监听到消息之后,做相应的处理。
Original file line numberDiff line numberDiff line change @@ -160,6 +160,16 @@ label = "boardconfig"; reg = <0x3f0000 0x10000>; read-only; nvmem-layout { compatible = "fixed-layout"; #address-cells = <1>; #size-cells = <1>; macaddr_boardconfig_16: macaddr@16 { reg = <0x...
[ 595.791790] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 595.800039] br-lan: port 2(wlan0) entered blocking state [ 595.807038] br-lan: port 2(wlan0) entered forwarding state #启动后可看到hostapd进程 root@OpenWrt:/# ps | grep hostapd ...
sudo iw dev wlan1 station get <peer-MAC-address> 在STA的情况下,上述的<peer-MAC-address>将是你的AP的MAC地址。 修改传输比特率 iw 支持修改发送的比特率,假托传统和 HT MCS速率。 这是通过设定允许的比特率掩码来实现,你也可以清除该掩码。
The FakeTCP mode does not behave 100% like a real tcp connection. ISPs may be able to distinguish the simulated tcp traffic from the real TCP traffic (though it's costly). seq-mode can help you change the seq increase behavior slightly. If you experience connection problems, try to change...
36、plug.d/button/change2ap option min 3 option max 8config button option button reset option action released option handler /etc/hotplug.d/button/change2dhcp option min 9 option max 99这样以后按住reset 2秒内, 3-8秒 和 9秒以上,会自动切换到对应的网络配置,并自动重启路由器。按住reset0-2秒...