https://wiki.openwrt.org/doc/recipes/relayclient 该方法可以实现中继AP,而不需要AP(WDS)模式。中继后,相当于该路由所有的LAN口以及AP热点都和上级路由在同一网段。如果要访问本路由的Luci,则要手动设置电脑的ip地址,和本路由的LAN ip在同一网段。 准备: 需要安装的组件: relayd luci-proto-relay 设置: (本...
https://wiki.openwrt.org/doc/recipes/relayclient 该方法可以实现中继AP,而不需要AP(WDS)模式。中继后,相当于该路由所有的LAN口以及AP热点都和上级路由在同一网段。如果要访问本路由的Luci,则要手动设置电脑的ip地址,和本路由的LAN ip在同一网段。 准备: 需要安装的组件: relayd luci-proto-relay 设置: (本...
option ra_mtu '1500' is set correctly in /etc/config/dhcp In LuCI though, RA MTU and RA Hop Limit are still displaying the default values in light gray font color. Expected behavior: Example: Replace the following lines and remove this RA MTU and RA Hop Limit are displaying the correct ...
此时就可以使用中继桥了。 menuconfig中勾选relayd编译进包内(网页安装luci-proto-relay亦可) 关闭本机设备的DHCP服务 扫描加入主路由的WiFi时,配置接口协议时选择中继桥(relay bridge),连接上级WiFi的接口设为LAN防火墙 其他正常填完配置后,回到接口页,编辑刚才新建的接口 把接口关联接口选择“lan”和连接上级WiFi的接...
首先在内核里面将relay模块编译进SDK,并重新烧写;此模块可实现二级路由同网段无线桥接功能: make menuconfig LuCI--->5.protocols---><*>luci-proto-relay 配置 配置目标 a、路由器使用station模式接受Wifi b、路由器使用AP模式发射Wifi c、连入中继路由器的设备也能访问外网且还处于原来的子网 配置...
luci-proto-relay: propagate up state, do not forward netifd errors jow- committedJul 28, 2018 aae187d Commits on Nov 10, 2017 protocols: fix various interface patterns jow- committedNov 10, 2017 932bae9 Commits on Jan 16, 2015 Update my email addresses in the license headers ...
需要安装两个插件:relayd,luci-proto-relay。 通过wifi 连接上级路由器。可以转发HDCP信息和IPV6信息。请按照自身网络环境修改wireless下对应的上级路由的SSID、MAC地址、密码和加密方式等后即可。 上传者:tsinghal时间:2020-02-13 openwrt编译全过程(超详细) ...
openwrt 执行lua脚本 openwrt - luci 先看看network的配置文件: [html]view plaincopy 1. config interface 'loopback' 2. option ifname 'lo' 3. option proto 'static' 4. option ipaddr '127.0.0.1' 5. option netmask '255.0.0.0' 6. 7. config interface 'lan'...
option proto 'static' option ipaddr '192.168.123.251' option gateway '192.168.123.1' 此时可以在内网的终端设备上通过 192.168.123.251 访问luci 界面进行配置。 配置旁路网关 openwrt 中 网络-接口-lan 设置: 基本设置: - 协议:静态 - ipv4: 192.168.123.251 - 网关: 192.168.123.1 - 自定义DNS: 114.114....
以上软件包可以在编译固件的时候 make menconfig 时直接编译到固件中,也可以在 luci 界面或命令行界面使用opkg 安装,最后的效果都是一样的。 构建好镜像,或者安装好这些软件包之后,就可以把模块插入软路由,插入之后,在 /dev 下面就可以找到 cdc-wdm0、ttyUSB0、ttyUSB1、ttyUSB2 和 ttyUSB3 接口,另外输入 dm...