eth0是一块物理网卡。eth0.1 eth0.2都是从此设备上虚拟出来的。 eth0.1 是vlan 1分出的lan口。 eth0.2 是vlan 2分出的wan口。 br-lan 虚拟设备,用于LAN口设备桥接,可以用brctl show查看使用情况。 ~brctlshowbridge name bridge id STP enabled interfaces br-lan7fff.64098005e1bbnoeth0.1rai0 ra0 br-lan...
eth0.1 eth0.2都是从此设备上虚拟出来的。 eth0.1 是vlan1分出的lan口。 eth0.2 是vlan分出的wan口。 br-lan 虚拟设备,用于LAN口设备桥接,可以用brctl show查看使用情况。 代码语言:javascript 代码运行次数:0 运行 AI代码解释 ~brctl show bridge name bridge idSTPenabled interfaces br-lan 7fff.64098005e1b...
wlan0=无线端口 在路由器中输入ifconfig命令,输出如下图: eth0 eth0是一块物理网卡。eth0.1 eth0.2都是从此设备上虚拟出来的。 eth0.1 是vlan1分出的lan口。 eth0.2 是vlan分出的wan口。 rao raio 这两个是成对出现,一看就知道是无线设备,它们各自对应一个SSID,分别是2.4G和5G。 br-lan br-lan 虚拟设...
eth0.1 是vlan 1分出的lan口。 eth0.2 是vlan 2分出的wan口。 br-lan 虚拟设备,用于LAN口设备桥接,可以用brctl show查看使用情况。 ~ brctl show bridge name bridge id STP enabled interfaces br-lan 7fff.64098005e1bb no eth0.1 rai0 ra0 1. 2. 3. 4. br-lan = eth0.1 + rai0...
官方Openwrt安装完毕后,默认情况下只配一个WAN口,一个LAN。通常默认第一个口(eth0)是LAN口,第二口(eth1)是WAN口。 而我打算将我的6口软路由器的第一个口(eth0)设置为WAN口,将剩余其他口(eth1、eth2、eth3、eth4、eth5)设置为LAN口。 操作 ...
网络-接口-设备中编辑br-lan,配置网桥端口为eth0eth1eth2保存并应用; 网络-接口中编辑LAN,常规设置iPv4网关为上级路由的网关(直连光猫拨号为192.168.1.1); 网络-接口中编辑LAN,高级设置使用自定义的 DNS 服务器(直连光猫拨号为192.168.1.1),也可以添加其他的自定义的 DNS 服务器; ...
将PVE eth3 作为管理口,接入硬路由 lan 。 BIOS 引导安装 系统 I agree同意 LICENSE Target Harddisk选择硬盘。 检查国家和时区是否正常(网络自动获取)。 设置管理密码。 填写企业服务邮箱(可略)。 配置网络: 自动识别联网的管理口(设备名),检查对应 eth3。
vrcons openwrt1 vrcons openwrt2 默认情况下,OpenWRT 的br-lan(eth0)是LAN接口, eth1是WAN接口, 查看br-lan信息 ifconfig br-lan 下面开始修改openwrt1的网络配置 查看lan网络配置 root@OpenWrt:/# uci show network.lan 修改lan网络配置 root@OpenWrt:/# uci set network.lan.ipaddr='10.0.0.15' 查...
globals 'globals' option ula_prefix 'fdf1:f344:c0d9::/48' config device option name 'br-lan' option type 'bridge' list ports 'eth0' config interface 'lan' option device 'br-lan' option ipaddr '192.168.1.1' option netmask '255.255.255.0' option ip6assign '60' option proto 'dhcp' ...