Config Command: ftdi layout_init data direction Specifies the initial values of the FTDI GPIO data and direction registers. Each value is a 16-bit number corresponding to the concatenation of the high and low FTDI GPIO registers. The values should be selected based on the schematics of the ada...
#ftdi_device_desc "USB<=>JTAG&RS232" #通过PID VID指定调试器,比描述更准确些 ftdi_vid_pid 0x1457 0x5118 #如果有多个同样的调试器,还可以指定要使用的调试器序列号 #ftdi_serial #引脚定义,相当于旧版中的 ft2232_layout jtagkey ftdi_layout_init 0x0c08 0x0f1b ftdi_layout_signal nTRST -data ...
#ftdi_device_desc "USB<=>JTAG&RS232" #通过PID VID指定调试器,比描述更准确些 ftdi_vid_pid 0x1457 0x5118 #如果有多个同样的调试器,还可以指定要使用的调试器序列号 #ftdi_serial #引脚定义,相当于旧版中的 ft2232_layout jtagkey ftdi_layout_init 0x0c08 0x0f1b ftdi_layout_signal nTRST -data ...
interface ftdi ftdi_device_desc "OpenOCD JTAG/SWD adapter" ftdi_layout_init 0x0008 0x000b ftdi_layout_signal nSRST -data 0x0020 ftdi_layout_signal nTRST -data 0x0010 transport select swd source [find target/stm32f4x.cfg] 在这个例子中,配置文件指定了使用FTDI接口,并通过SWD进行通信,同时指定了...
#ftdi_serial #引脚定义,相当于旧版中的 ft2232_layout jtagkeyftdi_layout_init0x0c080x0f1bftdi_layout_signal nTRST-data0x0100-noe0x0400ftdi_layout_signal nSRST-data0x0200-noe0x0800 此时可以尝试运行一下openocd,以检查连接和配置情况: 1.关闭设备电源, ...
ftdi_layout_init 0x0018 0x05fb # Enable SWD for the lines that we are using, and the port ftdi_layout_signal SWD_EN -data 0 # This is used to specify the sRST pin, in our case we're using ftdi_layout_signal nSRST -data 0x0010 ...
jtagftdi_layout_init 0x0008 0x001bftdi_layout_signal nSRST -oe 0x0020 -data 0x0020ftdi_layout_...
ftdi_device_desc "Digilent USB Device" ftdi_vid_pid 0x0403 0x6014 ftdi_channel 0 ftdi_layout_init 0x00e8 0x60eb reset_config none transport select jtag ### # Target: CYPRESS FX3 ARM926EJ-S ### if { [info exists CHIPNAME] } { set _CHIP...
use 'ftdi layout_init' not 'ftdi_layout_init' DEPRECATED! use 'adapter speed' not 'adapter_khz' adapter speed: 200 kHz Warn : Transport "jtag" was already selected Warn : imx6q.sdma: nonstandard IR value ../OpenOCD-20240916-0.12.0/bin/../share/openocd/scripts/board/fsl_imx6q_sabre...
MicroZus ZYNQ 7020开发板OpenOCD设置 # OpenOCD MicroZus interface ftdi ftdi_vid_pid 0x0403 0x6014 ftdi_layout_init 0x2088 0x3f8b transport select jtag reset_config srst_only srst_push_pull source [find target/zynq_7000.cfg] 1. 2. 3. 4. 5. 6. 7. 8....