你可以使用GDB(GNU调试器)来连接到OpenOCD进行调试。首先,你需要编译你的ESP32项目并生成调试信息。然后,使用GDB连接到OpenOCD: bash xtensa-esp32s3-elf-gdb build/your_project.elf 在GDB中,使用以下命令连接到OpenOCD: gdb target remote :3333 端口号3333是OpenOCD的默认调试端口,如果你使用了不同的端口,...
如图2-2-3-4所示,点击“Browse“配置OpenOCD启动文件,在”Config options“编辑框中输入JTAG调试器的配置文件。ESP-Prog所用的配置文件是esp32c3-ftdi.cfg,这个文件可以在OpenOCD的安装或解压目录的/share/openocd/scripts/ board目录中找到,如果想进一步了解关于OpenOCD更详细的资料,请自行上网查阅相关的资料。到此...
https://github.com/espressif/esp-nuttx-bootloader 然后,nuttx则需要自己编译。 在烧录esp32c3程序时,需要在电脑上安装python3。 pip install esptool 安装esptool就可以进行烧录了。 通过下面的命令烧录nuttx esptool.py --chip esp32c3 --port COM3 --baud 921600 write_flash 0x0 .\bootloader-esp32c3....
openocd -f interface/ftdi/esp32_devkitj_v1.cfg -f board/esp-wroom-32.cfg 1. 如果没有在系统中给 USB 口授权 OpenOCD 可能会启动失败。解决方法如下: 补充:openocd需要使用usb,需要把( idf 4.0 ) .espressif/tools/openocd-esp32/v0.10.0-esp32-20190708/openocd-esp32/share/openocd/contrib/60...
没有esp32的cfg 使用官方OpenOCD,配置文件使用乐鑫的,CMSIS-DAP可以正常识别,但确实不支持ESP32芯片 F:\Espressif\tools\openocd-esp32\v0.11.0-esp32-20220706\openocd-esp32\share\openocd\scripts>openocd -f interface/cmsis-dap.cfgOpenOn-Chip Debugger0.11.0(2021-11-18) [https://github.com/sysprogs...
ESP32S3之JTAG调试OPENOCD服务启动失败 OpenOCD server is not running! [OpenOCD] ❌ Error: libusb_open() failed with LIBUSB_ERROR_NOT_FOUND [OpenOCD] ❌ Error: esp_usb_jtag: could not find or open device! OpenOCD打开不成功主要是驱动程序不对...
esp: Added a problem hints file to the distribution. It is intended for IDEs to suggest possible solutions to users based on error output in the OpenOCD log. Fixes: target/esp32p4: Custommintstatusdeclaration due to the changed register number. Can be accessed ascsr_mintstatus. ...
对于esp32c3裸机开发,用openocd结合gdb非常的有用,这是裸机开发的关键工具。 esp32c3的开发支持两种调试方式,分别是内置的USB调试接口,以及外扩的扩展调试接口。其内置一个USB-to-JTAG的接口。 1.1 内置的JTAG接口 由于esp32c3芯片内置一个JTAG的调试器的引擎,所以不用外置的JTAG的调试器。其中的硬件连接可以参考...
v0.11.0-esp32-20211220 Operating System FreeRTOS Using an IDE ? Eclipse OpenOCD command line openocd.exe -f board/esp32s2-bridge.cfg -c "program_esp C:/Users/e0629509/Smart_Signaling/build/esp32_sample_app.bin 0x1000 verify exit" ...
Warn : esp32.cpu0: Failed reading 4 bytes at address 0x00000000 Interrupt suppression during single-stepping is now enabled Error: JTAG scan chain interrogation failed: all ones Error: Check JTAG interface, timings, target power, etc.