上一篇文章我们学习了 OpenOCD 注册命令的过程,这一篇我们来年一下 OpenOCD 执行命令的逻辑。 1从 openocd_thread() 开始 1)从 main() 函数到 openocd_main() 函数,最后我们来看 openocd_thread() 函数的执行逻辑: 2)openocd_thread() 的逻辑一共有 7 个步骤: (1)通过 parse_cmdline_args() 解析open...
openocd failed with code (1) 经过检查我们发现此错误是由于配置中默认文件路径有误导致的,在默认模板中,elf文件的路径中使用的是“/”,而windows系统默认文件路径是“\”,所以导致elf文件无法识别而无法下载。解决办法一是手动修改斜杠符号,二是双击“GDB OPenOCD Debugging”生成新的配置卡片,此时默认的斜杠方向...
目录概述1 main()2 setup_command_handler()3 register_commands()3.1 server_register_commands()3.2 register command 概述 1)OpenOCD 与调试器、MCU 的关系: (1)OpenOCD 运行在
# 克隆代码 git clone https://git.code.sf.net/p/openocd/code openocd # 克隆指定版本的代码 # git clone -b 2.20.3 --depth=1 https://git.code.sf.net/p/openocd/code openocd # 进入目录 cd openocd # OpenOCD,启动 ./bootstrap 3.2 配置 OpenOCD 1)这里的 “--enable-ftdi” 对于我这...
while (1) { /* LED灯每1s闪烁 */ HAL_Delay(1000); //延时1S a++; //每1秒a加1 HAL_GPIO_TogglePin(GPIOE,GPIO_PIN_8); // 翻转LED灯状态 /* USER CODE END WHILE */ /* USER CODE BEGIN 3 */ } 四、开始调试 1.点击“开始调试F5” 2.选择变量“a”,将其添加到监视 3.在a++的下一...
OpenOCD可以与多种开发环境集成,如Eclipse、Visual Studio Code等。通过与开发环境的集成,可以实现更便捷的调试和烧录操作。 四、OpenOCD的应用场景 1. 嵌入式系统开发 OpenOCD广泛应用于嵌入式系统的开发过程中,可以用于调试和烧录各种类型的嵌入式设备,如单片机、嵌入式Linux等。 2. 驱动开发和调试 OpenOCD可以用于...
注意到idcode不对,这个比较简单,复制一个`stm32f1x.cfg`的target file,改为`gd32e23x.cfg`,把里面的idcode改成它期望的数值,然后再试一次: openocd -s conf/ -f conf/openocd.cfgOpen On-Chip Debugger 0.11.0-rc1-snapshot (2020-12-10-11:15)Licensed under GNU GPL v2For bug reports, readhttp...
src/freertos: Fixed target memory cleanup. If the target is running post reset, we still need to cleanup OpenOCD's rtos variables, but we cannot touch the target memory as the application code will clean it, and might have already updated the memory with new data. ...
I think the codebase I'm working with is designed to work with Segger JTAG debuggers too so I'm not sure how much I can change at this point. In some ways it's good to have a ton to work with when you start a new job. In other ways it means there's a ton to learn and ...
However, programming an older code via Wiced Studio with either STlink or Jlink through OpenOCD no longer works. I'm unsure if it's a driver problem or something else, but do you have a solution to simply connect to an STM32F415 using Wiced Studio tools? I've reinstalled Wiced Studio...